Approximate Capacities
Engine Crankcase (Refill Capacity) - ... 23 U.S. Quarts
Engine Cooling System - ... 23 U.S. Gallons
Fuel Tank - ... 200 U.S. Gallons
Water Tank - ... 700 U.S. Gallons
Main Hydraulic Oil Tank - ... 60 U.S. Gallons
Hydraulic Oil Replenishing Tank - ... 9.5 U.S. Gallons
Air Line Lubricator - ... 1/2 U.S. Pint
Cutter Drum (50% Solution of Water and Ethylene Glycol Antifreeze) - ... 40 U.S. Gallons
Fuel
No. 2D diesel fuel with a minimum cetane rating of 40 in the summer and 45 in the winter and a maximum sulfer content of 0.50%.
Lubricants And Oils
CO - Diesel Engine Crankcase Oil (CMI No. A05265)
- 1. Type: Engine oil meeting SAE designation CD or MIL-L-2104C.
- 2. Viscosity: SAE 40 or 30.
- 3. Vendor: Mobil Delvac 1300 Series or equivalent.
- 2. Viscosity: SAE 40 or 30.
BR - Multipurpose Grease (CMI No. A05536)
- 1. Type: Multipurpose grease as defined by SAE J310a.
- 2. Consistency: NLGI No. 1
- 3. Vendor: Mobilux EP-1, Mobil Grease MP, or equivalent.
- 2. Consistency: NLGI No. 1
GL - Gear Lubricant (CMI No. A05535)
- 1. Type: Axle and manual transmission lubricant meeting API designations GL-5 or GL-6 as defined in SAE J308a.
- 2. Viscosity: SAE 90 as defined in SAE J306a.
- 3. Vendor: Mobilgear 630, or equivalent.
- 2. Viscosity: SAE 90 as defined in SAE J306a.
LB - Bearing Lubricant (CMI No. A03306)
- 1. Type: Code No. 995 Multifak EP 2. NO SUBSTITUTES.*
- 2. Consistency: NLGI No. 2.
- 3.Vendor: Texaco Multifak EP 2.
- 2. Consistency: NLGI No. 2.
HO - Hydraulic System Oil (CMI NO. A05533)
Automatic Transmission Fluid, Type F, meets Ford Motor Company Specification ESW-M2C33-F.
LG - Leg Barrel Grease (CMI No. A03305)
- 1. Type: Molybdenum disulfide or graphite adhesive black grease.
- 2. Consistency: NLGI No. 2.
- 3. Vendor: Code No. 1956 Texclad 2 or equivalent.
- 2. Consistency: NLGI No. 2.
CC - Crankcase Oil for Airline Lubricator
- 1. Type: Non-detergent automotive engine oil.
- 2. Viscosity: SAE 10W.
*Wichita Clutch Company required lubricant for use in power take-off.
Engine Cooling System Antifreeze
Ethylene glycol type permanent antifreeze (CMI No. A05268). Recommended mixture - 50% antifreeze and 50% clean mineral-free water.
*See page 5-1 for lubricant specifications.
**Oil in the gear reducers should be changed after first 50 hours.
***Raise the machine all the way and then lower it evenly 2 1/2inches so that the top ring of each yoke is lined up with grease fittings.
KEY TO SYMBOLS:
- C - Change
- L - Lubricate
- W - Wash
- X - Check, add appropriate liquid when needed
- L - Lubricate
NOTES:
- A. Apply lubricant only until resistance is felt on handle of grease gun.
- B. Apply one shot of lubricant.
- C. Check coolant level and clean radiator and oil cooler cores daily.
- D. Change as required by indicator.
- E. Lubricate slowly until excess lubricant is observed.
- F. No regular service required. See maintenance manual for repair procedures.
- G. Fill to check plug level.
- H. Change supply or return filter elements when indicator is red & hydraulic oil temperature is above 100°F.
- B. Apply one shot of lubricant.
![]() |
HYDRAULIC SYSTEMS WILL NOT OPERATE WITH DIRTY HYDRAULIC OIL FILTERS. A SUPPLY OF FILTER ELEMENTS AT JOB LOAVSION IS MANDATORY. RE-ORDER ELEMENTS WHEN SUPPLY RUNS LOW. HYDRAULIC OIL RETURN FILTER ELEMENT NO. 2-8403 HYDRAULIC OIL SUPPLY FILTER ELEMENT NO. 2-8403 HYDRAULIC OIL AUXILIARY SYSTEM FILTER ELEMENT NO. 2-8425-001 |
![]() |
- I. Change auxiliary pressure filter element if operation of hydraulic cylinders becomes sluggish.
- J. Lubricate leg yokes by hand whenever grease on yokes is worn thin.
- K. If roto coupling has lube fitting, check daily and lubricate as needed. Do not over-lubricate.