Specifications
`
561N Pipelayer
[SEBU7674]
ENGINE ARRANGEMENT
561M Pipelayer
Engine Starting with Jump Start Cables
561N Pipelayer
Specifications
561N Pipelayer
Plate Locations and Film Locations
1.1. Intended Use
2.2. Restrictions to Application and Configuration
The standard machine shipping specifications are listed in Table 1.
Show/hide table
561N Pipelayer     | |
Approximate operating weight of the standard machine     | 16851 kg (37150 lb)     |
Weight of the machine without the boom, the boom sheave blocks, and the load blocks     | 15921 kg (35100 lb)     |
Length of the machine     | 3708 mm (12 feet 2 inch)     |
Width of the machine without the counterweight and the boom     | 2983 mm (9 feet 9 inch)     |
Width of the machine with the counterweight fully extended.     | 4463 mm (14 feet 8 inch)     |
Height of the machine without the boom     | 3041 mm (10 feet 0 inch)     |
Height of the machine with the boom     | 6362 mm (20 feet 10 inch)     |
Ground clearance of the machine     | 432 mm (1 foot 5 inch)     |
Intended Use
This machine is a Pipelayer that is described in ISO 6165:2001. The machine is intended to perform the following functions: lift, handle and lay down pipe with a side mounted boom.
Restrictions to Application and Configuration
Maximum approved operating weight is 17300 kg (38145 lb).
The maximum lift capacity is 18144 kg (40000 lb).
The maximum fore and aft slope is 45 degrees or a 100 percent grade for the proper lubrication of the pipelayer .
Information System:
12H Motor Grader
Reference Material
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Steering System
Piston Pump (Steering) Margin Pressure - Test and Adjust
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Steering System
Piston Pump (Steering) Low Pressure Standby - Test
120H and 135H Motor Graders Machine Systems
Air Control Valve (Parking Brake) - Disassemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Steering System
Steering System Pressure (High Pressure Stall) - Test
R2900 Load Haul Dump
Steering and Transmission Lock Control (STIC Steering)
R2900 Load Haul Dump
Braking
120H and 135H Motor Graders
Reference Material
D350E Series II and D400E Series II Articulated Trucks Power Train
Differential and Bevel Gear
3508B Engine for D11R Track-Type Tractors
Event Codes
247 and 257 Multi Terrain Loaders
Quick Coupler
D350E Series II and D400E Series II Articulated Trucks Power Train
Transmission Planetary
120H and 135H Motor Graders
Safety Messages
561N Pipelayer
Plate Locations and Film Locations
793C XQ Off-Highway Truck and 793C Off-Highway Truck Engine Supplement
Radiator - Install
3054E Industrial Engine
Engine Oil Filter
CB-634D Paving Compactor Machine Electronic Control System
Water Spray Is Always Off
CB-534D, CB-534D XW and CB-564D Vibratory Asphalt Compactors Propel System
Drum Drive Group
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes
Service Brakes and Retarder System Leakage - Check
216 and 232 Skid Steer Loaders 3024 Engine Supplement
Pump Mounting - Remove and Install
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders
Features
554 and 574 Forwarders Power Train
Gearshift Pressures - Test - 574 Forwarder 1FM434-UP
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes
Service Brakes and Retarder System Pressure - Test
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System
Proportional Pressure Solenoid Valve - Test