561N Pipelayer Plate Locations and Film Locations Caterpillar


Plate Locations and Film Locations
`
1.1. Certification
2.2. ROPS
3.2. European Union
4.2. Machine Security System
5.2. Sound

The Product Identification Number (PIN) will be used to identify a powered machine that is designed for an operator to ride.

AVSpare products such as engines, transmissions and major attachments that are not designed for an operator to ride are identified by Serial Numbers.

For quick reference, record the identification numbers in the spaces that are provided below the illustration.




Illustration 1g00650398

The machine PIN is located at the rear of the machine on the left side of the transmission housing.

Machine PIN ____________________




Illustration 2g00189280

Service Information Number Plate (SIN) ____________________




Illustration 3g01009202

Transmission Serial Number ____________________




Illustration 4g00860883

The engine serial number is located on top of the engine valve cover.

Engine Serial Number ____________________

Certification

ROPS

If equipped, this message is positioned on the vertical support of the ROPS on the right side of the machine.




Illustration 5g01010089

------ WARNING! ------

Structural damage, an overturn, modification, alteration, or improper repair, can impair this structure's protective capability thereby voiding this certification. Do not weld on or drill holes in the structure. Consult a AVSpare dealer to determine this structure's limitations without voiding its certification.

----------------------

This machine has been certified to the standards that are listed on the certification film. The maximum mass of the machine, which includes the operator and the attachments without a payload, should not exceed the mass on the certification film.

A typical example of the certification film is shown above.

Refer to Operation and Maintenance Manual, "Guards (Operator Protection)" for more information.

European Union




Illustration 6g00039984

This plate is positioned on the left side of the front frame.

  • PIN____________________

  • Model____________________

  • Power (kW)____________________

  • Weight (kg)____________________

Machine Security System

If equipped, this message is used to verify the certification of the Machine Security System as a RF transmitter. The following specifications are provided to aid in ensuring compliance with all local regulations:

Table 1
Field strength (1)     16.12 dB micro-amp/meter    
Operating frequency range     134.2 kHz    
Operating time (2)     0.055 seconds (1/18 second)    
( 1 ) Field strength at 10 meters
( 2 ) The operating time is measured after the key switch is first activated.

This message is located on the control group for the machine security system. The control group is located in the engine compartment.




Illustration 7g00995393

Consult your AVSpare dealer with any questions that concern the operation of the MSS in a specific country.

Sound




Illustration 8g00933634

A typical example of this film is shown. Your machine may have a different value.

If equipped, the certification film is used to verify the environmental sound certification of the machine. The value that is listed on the film indicates the guaranteed sound power level. The guaranteed sound power level is measured at the time of manufacture. The guaranteed sound power level is measured according to the conditions that are specified in "2000/14/EC".

Information System:

120H and 135H Motor Graders Safety Messages
561N Pipelayer Specifications
12H Motor Grader Reference Material
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Steering System Piston Pump (Steering) Margin Pressure - Test and Adjust
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Steering System Piston Pump (Steering) Low Pressure Standby - Test
120H and 135H Motor Graders Machine Systems Air Control Valve (Parking Brake) - Disassemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Steering System Steering System Pressure (High Pressure Stall) - Test
R2900 Load Haul Dump Steering and Transmission Lock Control (STIC Steering)
R2900 Load Haul Dump Braking
120H and 135H Motor Graders Reference Material
D350E Series II and D400E Series II Articulated Trucks Power Train Differential and Bevel Gear
3508B Engine for D11R Track-Type Tractors Event Codes
793C XQ Off-Highway Truck and 793C Off-Highway Truck Engine Supplement Radiator - Install
3054E Industrial Engine Engine Oil Filter
CB-634D Paving Compactor Machine Electronic Control System Water Spray Is Always Off
CB-534D, CB-534D XW and CB-564D Vibratory Asphalt Compactors Propel System Drum Drive Group
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes Service Brakes and Retarder System Leakage - Check
216 and 232 Skid Steer Loaders 3024 Engine Supplement Pump Mounting - Remove and Install
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Features
554 and 574 Forwarders Power Train Gearshift Pressures - Test - 574 Forwarder 1FM434-UP
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes Service Brakes and Retarder System Pressure - Test
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System Proportional Pressure Solenoid Valve - Test
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Electronic Control Module (Power Train)
CB-534D, CB-534D XW and CB-564D Paving Compactors Machine Systems Radiator and Hydraulic Oil Cooler