Loading, Hauling and Dumping
`
R2900 Load Haul Dump
[SEBU7325]
R2900 Load Haul Dump
Operating Technique Information
R2900 Load Haul Dump
Bucket Loading Hauling Units
MACHINE ARRANGEMENT
- Position the bucket parallel to the ground. The bucket should barely skim the ground. Drive the bucket straight into the pile.
Show/hide table
 | |
| Illustration 1 | g00945024 |
- Move the joystick control lever to the RAISE position as forward movement slows. Return to the HOLD position for additional tilt back power.
Show/hide table
 | |
| Illustration 2 | g00945025 |
- To fill the bucket, work the joystick control lever back and forth from the TILT BACK to the HOLD position while continuing to use RAISE as required to reduce wheel slip.
Show/hide table
 | |
| Illustration 3 | g00945026 |
- When the bucket is loaded, move the joystick control lever to the TILT BACK position.
Show/hide table
 | |
| Illustration 4 | g00945028 |
- Raise the bucket high enough to clear the material being loaded. Tilt the bucket back until the bucket contacts the stops. Always carry the load with the bucket in the fully tilted back position to avoid material spillage and minimize loader linkage wear.
Show/hide table
 | |
| Illustration 5 | g00945029 |
- Move the transmission direction and speed control to the REVERSE position. Carry the loaded bucket approximately 400 mm (15 inch) above the ground level.
- When reaching the dump area, move the joystick control lever to the RAISE position.
Show/hide table
 | |
| Illustration 6 | g00945030 |
- When at the correct height, move the joystick control lever to the DUMP position.
Show/hide table
 | |
| Illustration 7 | g00945031 |
- To control dumping, move the joystick control lever to the DUMP position. Then, return the lever to the HOLD position. Repeat this procedure until the bucket is empty.
Show/hide table
 | |
| Illustration 8 | g00945034 |
- To achieve the maximum angle for dumping, use the stops for the bucket.
Show/hide table
 | |
| Illustration 9 | g00945033 |
Show/hide table
| NOTICE |
|---|
Striking the stops unnecessarily and repetitively can result in accelerated wear and high maintenance cost of the loader linkage. |
Information System:
R2900 Load Haul Dump
Operating Technique Information
3500 and 3500B High Displacement Engines for Caterpillar Built Machines
Water Pump - Install
R2900 Load Haul Dump
Engine and Machine Warm-Up
R2900 Load Haul Dump
Engine Starting with Auxiliary Start Receptacle
140H and 160H Motor Graders Engine Supplement
Refrigerant Compressor - Remove and Install
R2900 Load Haul Dump
Engine Starting with Jump Start Cables
Hitch Bore and Steering Cylinder Bore Dimensions for Wheel Skidders and Feller Bunchers{4303, 7051}
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes
Brake Hydraulic System
3500 and 3500B High Displacement Engines for Caterpillar Built Machines
Auxiliary Water Pump - Assemble
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train
Torque Converter
793C XQ Off-Highway Truck and 793C Off-Highway Truck Engine Supplement
Modular Front End - Install
D350E Series II and D400E Series II Articulated Trucks Power Train
Final Drive and Wheel
2002/11/18
A New Drum Propel Motor and Final Drive Is Now Used on Certain Vibratory Soil Compactors {4351, 6605}
3500 and 3500B High Displacement Engines for Caterpillar Built Machines
Air Compressor - Remove and Install
120H and 135H Motor Graders Machine Systems
Bank Valve - Disassemble - Bank Valve with Hydraulic Detent
D350E Series II and D400E Series II Articulated Trucks Power Train
Rear Drive Shaft
12H Motor Grader Engine Supplement
Refrigerant Condenser - Remove and Install
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System
Lift Kickout - Adjust - Integrated Toolcarrier
140H and 160H Motor Graders Engine Supplement
Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System
Work Tool Positioner - Adjust - Integrated Toolcarrier
550, 570 and 580 Wheel Harvesters
Safety Messages
550, 570 and 580 Wheel Harvesters
Specifications
D350E Series II and D400E Series II Articulated Trucks Power Train
Selector and Pressure Control Valve
RM-350B Road Reclaimer/Soil Stabilizer Machine Systems
Hydraulic Cylinder (Front Steering) - Remove and Install