938G II Wheel Loader and IT38G II Integrated Toolcarrier Additional Messages Caterpillar


Additional Messages
`
1.1. Lifting or Tying Down the Machine (1)
2.1. Air Conditioner (2)
3.1. Radial Seal Air Filters (3)
4.1. No Step (4)

There are several specific messages on this machine. The exact location of the messages and the description of the messages are reviewed in this section. Please become familiarized with all messages.



Illustration 1g01069739

Make sure that all of the messages are legible. Clean the messages or replace the messages if you cannot read the words.

When you clean the messages, use a cloth, water and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the messages. Loose adhesive will allow the messages to fall.

Replace the illustrations if the illustrations are not legible. Replace any message that is damaged, or missing. If a message is attached to a part that is replaced, install a message on the replacement part.

Consult your AVSpare dealer for replacement of messages.

Lifting or Tying Down the Machine (1)

This message is located on the left side of the machine.



Illustration 2g01070801

Reference: For more information, refer to Operation and Maintenance Manual, "Lifting and Tying Down the Machine".

Air Conditioner (2)

This message is located on the left cab door.



Illustration 3g00983944

Radial Seal Air Filters (3)

This message is located on the cover for the engine air filter.



Illustration 4g01070791


NOTICE

This machine uses radial seal type air cleaners. To avoid engine damage, use only radial seal replacement filters. Others will not seal.

Radial seal filter gasket design and location are critical to proper air cleaner operation. Use only AVSpare replacements.


No Step (4)

This message is centered on the top of the hood.



Illustration 5g00906093

Do not use the hood as a step. Deformation of the hood can occur.

Information System:

R2900 Load Haul Dump Stopping the Machine
CB-534D and CB-564D Asphalt Compactors Belts - Inspect/Adjust/Replace
R2900 Load Haul Dump Bucket Loading Hauling Units
320B, 320B L and 320B N Excavators Reference Material
3524B Engine for Caterpillar Built Machines Bearing Clearance - Check
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Transmission Oil Cooler - Remove and Install
550, 570 and 580 Wheel Harvesters Maintenance Interval Schedule
RM-350B Road Reclaimer/Soil Stabilizer Machine Systems Hydraulic Cylinder (Front Steering) - Remove and Install
D350E Series II and D400E Series II Articulated Trucks Power Train Selector and Pressure Control Valve
550, 570 and 580 Wheel Harvesters Specifications
550, 570 and 580 Wheel Harvesters Safety Messages
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System Work Tool Positioner - Adjust - Integrated Toolcarrier
140H and 160H Motor Graders Engine Supplement Water Separator and Fuel Filter (Primary) - Remove and Install
Troubleshooting Compressed Air System Components and Performance{1803, 5500}
143H and 163H Motor Graders 3176C Engine Supplement Battery - Remove and Install
R2900 Load Haul Dump Before Operation (Remote Control)
R2900 Load Haul Dump Operation (Remote Control)
R1600 Load Haul Dump Hydraulic System Relief Valve (Lift Circuit) - Test and Adjust
R1600G Load Haul Dump Hydraulic System Sequence Valve (Float) - Test and Adjust
14H Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Assemble
14H Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Disassemble
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Aftercooler - Remove and Install - Aftercooler Housing with 12 bolts
2002/09/16 An Updated Air Starting Control Group Improves Durability of the Lines {5500, 5501}
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Braking System Vane Pump (Implement, Pilot, Brake)