- Landfill Compactor:
- 826G Series II (S/N: AYH1-UP)
- 826G (S/N: 7LN1-UP)
- 836G (S/N: 7MZ1-UP; BRL1-UP)
- 826G (S/N: 7LN1-UP)
Introduction
This Special Instruction provides information on replacing the fuel lines. Higher abrasion resistant hose is now used. The new hose will improve the durability of the fuel line.
Do not perform any procedure in this publication or order any parts until you understand the information that is contained in this publication.
Machine Preparation
- Move the machine to a surface that is smooth, hard, and level. Move the machine to an area that is away from operating machines and away from personnel.
- Install blocks on the front and the rear of the front wheels.
- Install the steering frame lock.
826G (S/N: 7LN) Landfill Compactor
Qty     | Old Part Number     | Part Name     | Qty     | New Part Number     | Part Name     |
1     | 6N-4447     | Hose Assembly     | 1     | 267-8854     | Hose Assembly     |
1     | 9N-5279     | Hose Assembly     | 1     | 268-2977     | Hose Assembly     |
1     | 6N-1047or 116-2579     | Hose Assembly or Hose Assembly     | 1 1 1 1     |
267-8853 1B-2713 2W-2494 9M-1974     |
Hose Assembly Bolt Spacer Hard Washer     |
Note: Use the same routing as the previous fuel line. Also make sure that the new fuel lines are not rubbing on any surface.
![]() | |
Illustration 1 | g01389518 |
Location of Hose Assemblies |
- Remove old hose assemblies.
- Reuse the clips that are in good condition. Replace worn clips with 8M-2773 Clips .
- Install 267-8853 Hose Assembly (1), 268-2977 Hose Assembly (2), and 267-8854 Hose Assembly (3) on the machine.
Note: Orient 267-8853 Hose Assembly (1) and 268-2977 Hose Assembly (2) at the angle that is shown in Illustration 3.
![]() | |
Illustration 2 | g01389523 |
Left side of the engine |
- Install 2W-2494 Spacer (4), 9M-1974 Hard Washer (5), and 1B-2713 Bolt (6) on the machine.
![]() | |
Illustration 3 | g01389577 |
(A) 30° ± 10° |
826G Series II (S/N: AYH) Landfill Compactor
Qty     | Old Part Number     | Part Name     | Qty     | New Part Number     | Part Name     |
1     | 6W-2409     | Hose Assembly     | 1     | 257-4155     | Hose Assembly     |
1     | 172-8827     | Hose Assembly     | 1     | 255-1257     | Hose Assembly     |
1     | 113-9000     | Hose Assembly     | 1     | 267-8849     | Hose Assembly     |
1     | 160-9449     | Hose Assembly     | 1     | 267-8850     | Hose Assembly     |
1     | 137-5094     | Hose Assembly     | 1 1 1 2 1 1     |
240-2015 7T-0266 0S-1588 5M-2894 067-2551 0L-1351     |
Hose Assembly Bracket Assembly Bolt Hard Washers Clip Bolt     |
Note: Use the same routing as the previous fuel line. Also make sure that the new fuel lines are not rubbing on any surface.
![]() | |
Illustration 4 | g01389518 |
Location of Hose Assemblies |
- Remove the old hose assemblies.
- Reuse the clips that are in good condition. Replace worn clips.
- Install 257-4155 Hose Assembly (1), 267-8850 Hose Assembly (2), 240-2015 Hose Assembly (3), 267-8849 Hose Assembly (4), and 255-1257 Hose Assembly (5) on the machine.
Note: Orient 240-2015 Hose Assembly (3) at the angle that is shown in Illustration 6.
![]() | |
Illustration 5 | g01389590 |
- Install 7T-0266 Bracket Assembly (9) on the machine. Also install 067-2551 Clip (6), two 5M-2894 Hard Washers (7), 0L-1356 Bolt (8), and 0S-1588 Bolt (10) on the machine.
![]() | |
Illustration 6 | g01389604 |
View A-A (A) 25° ± 5° |
- Install 0S-0948 clip (11) on the machine. Orient 0S-0948 clip (11) in the position that is shown in Illustration 7.
![]() | |
Illustration 7 | g01389608 |
Area A-A (B) 15° ± 5° |
836G (S/N: 7MZ) Landfill Compactor
Qty     | Old Part Number     | Part Name     | Qty     | New Part Number     | Part Name     |
1     | 9V-9295     | Hose Assembly     | 1     | 267-8845     | Hose Assembly     |
1     | 113-9002     | Hose Assembly     | 1     | 267-8846     | Hose Assembly     |
1     | 116-5416     | Hose Assembly     | 1     | 267-8847     | Hose Assembly     |
1     | 136-9141     | Hose Assembly     | 1     | 266-2872     | Hose Assembly     |
1     | 137-5094     | Hose Assembly     | 1 1 1 2 1     |
166-7952 0S-1594 1S-6420 5M-2894 9S-8752     |
Hose Assembly Bolt Clip Hard Washers Nut     |
Note: Use the same routing as the previous fuel line. Also make sure that the new fuel lines are not rubbing on any surface.
![]() | |
Illustration 8 | g01389611 |
Location of Hose Assemblies |
- Remove old hose assemblies.
- Reuse the clips that are in good condition. Replace worn clips with 067-2551 Clips .
- Install 266-2872 Hose Assembly (1), 267-8847 Hose Assembly (2), 267-8845 Hose Assembly (3), 267-8846 Hose Assembly (4), and 166-7952 Hose Assembly (5) on the machine.
![]() | |
Illustration 9 | g01389612 |
- Install 1S-6420 Clip (6) on the machine.
![]() | |
Illustration 10 | g01390742 |
- Install 0S-1594 Bolt (7), two 5M-2894 Hard Washers (8), and 9S-8752 Full Nut (9) on the machine.
836G (S/N: BRL) Landfill Compactor
Qty     | Old Part Number     | Part Name     | Qty     | New Part Number     | Part Name     |
1     | 9V-9295     | Hose Assembly     | 1     | 255-1255     | Hose Assembly     |
1     | 113-9002     | Hose Assembly     | 1     | 255-1256     | Hose Assembly     |
1     | 172-8827     | Hose Assembly     | 1     | 255-1257     | Hose Assembly     |
1     | 137-5094     | Hose Assembly     | 1     | 240-2015 4D-7735     |
Hose Assembly Clip     |
1     | 8S-1162 (1)     | Hose Assembly     | 1     | 255-1254     | Hose Assembly     |
1     | 116-2579 (1)     | Hose Assembly     | 1 1 1 2 1     |
255-1254 0S-1591 067-2551 5M-2894 030-7962     |
Hose Assembly Bolt Clip Washers Elbow     |
( 1 ) | The 8S-1162 Hose Assembly and the 116-2579 Hose Assembly are used for the same connection. Identify the hose assembly that is on your machine. Order the correct parts accordingly. |
Note: Use the same routing as the previous fuel line. Also make sure that the new fuel lines are not rubbing on any surface.
![]() | |
Illustration 11 | g01390667 |
Location of Hose Assemblies |
- Remove old hose assemblies.
- Reuse the clips that are in good condition. Replace worn clips with 067-2551 Clips .
- Install 030-7962 Elbow (1) on the machine.
![]() | |
Illustration 12 | g01389780 |
- Install 255-1254 Hose Assembly (2), 255-1257 Hose Assembly (6), 255-1255 Hose Assembly (7), 240-2015 Hose Assembly (8), and 255-1256 Hose Assembly (9) on the machine.
- Install 0S-1591 Bolt (3), two 5M-2894 Hard Washers (4), and 067-2551 Clip (5) on the machine.
- Install 4D-7735 Clip (10) on the machine.
![]() | |
Illustration 13 | g01390749 |