Installation Procedure for New 190-3692 Pressure Sensor {1408, 3016} Caterpillar


`
Installation Procedure for New 190-3692 Pressure Sensor {1408, 3016} [REHS1397]
ELECTRICAL AND STARTING SYSTEM
SENSOR GP
Installation Procedure for New 190-3692 Pressure Sensor {1408, 3016}
1.1. Introduction
2.1. Rework Procedure for the 190-3692 Pressure Sensors that are used for the Engine Oil, Charge Pressure, and Gearbox Pressures
Forwarders:
554 (S/N: 1AM1-UP)
574 (S/N: 1FM1-UP)

Introduction

New pressure sensors for the engine oil, the gearbox, and the charge pressure are used. The new pressure sensors use improved connectors that increase service life. The new sensors also use an internal orifice that reduces pressure spikes.

The new 190-3692 Pressure Sensor was effective with 554 (S/N: 1AM233-UP) and 574 (S/N: 1FM272-UP) Forwarders. The new 190-3692 Pressure Sensor replaces the former 162-8557 Pressure Sensor . The new pressure sensors are adaptable to first production of the machines that are listed.

The new pressure sensors use new connectors. The wiring harness of the machine must be modified when you are using the new pressure sensors. Use the following instructions in order to modify the harness.

Rework Procedure for the 190-3692 Pressure Sensors that are used for the Engine Oil, Charge Pressure, and Gearbox Pressures




Illustration 1g00908625

Location of the sensors




Illustration 2g00908627

554 Forwarder pressure sensor group

(1) Pressure Sensor for the Gearbox

(2) Pressure Sensor for the Charge Pressure

(3) Pressure Sensor for the Engine Oil




Illustration 3g00908630

574 Forwarder pressure sensor group

(1) Pressure Sensor for the Gearbox

(2) Pressure Sensor for the Charge Pressure

(3) Pressure Sensor for the Engine Oil

Table 1
Parts List    
Part Number     Quantity     Description    
186-3736 (1)     12     Socket    
155-2271 (1)     3     Plug Assembly    
8T-8737 (1)     3     Plug    
9U-7250 (2)     1     Deutch Connector Kit with Crimping Tool    
( 1 ) This part is included in the Deutch Connector Kit.
( 2 ) The 102-8809 Connecting Plug Kit that is listed in this kit has been replaced by a 155-2271 Connecting Plug Kit .

  1. Stop the engine. Turn off the battery disconnect switch.

  1. Mark the location of each wire in the connector for each 162-8557 Pressure Sensor that is replaced by a 190-3692 Pressure Sensor . Disconnect the harness from the existing pressure sensors. Cut the wires for the machine harness near the existing connector.

  1. Install one 186-3736 Connector Socket onto each of the wires. Install each wire of the machine harness into the correct pins of the 155-2271 Connecting Plug Kit . Refer to the following table for the correct pin out.

    Table 2
    Pin Out Chart    
    Sensor     Pin     Circuit     Wire Number    
    Engine Oil     1     Signal     405-GY    
    2 + V REF     997-OR    
    3 - V REF     993-BR    
    4 Shield     8T-8737    
    Gear Box Oil     1     Signal     730-BR    
    2 + V REF     997-OR    
    3 - V REF     993-BR    
    4 Shield     8T-8737    
    Charge Oil     1     Signal     731-BU    
    2 + V REF     997-OR    
    3 - V REF     993-BR    
    4 Shield     8T-8737    

  1. Install the new pressure sensors. Connect the machine harness to the correct pressure sensor.

Information System:

938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0615 - FMI 00
216 and 232 Skid Steer Loaders 3024 Engine Supplement Alternator - Remove and Install
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0613 - FMI 06
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0613 - FMI 05
3524B Engine for Caterpillar Built Machines Engine Oil Cooler - Assemble
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0613 - FMI 03
143H and 163H Motor Graders All Wheel Drive Location of Electrical Components
R2900 Load Haul Dump Fire Suppression System (Foam) - If Equipped
R2900 Load Haul Dump Engine Start Switch
3524B Engine for Caterpillar Built Machines Engine Oil Cooler - Disassemble
D250E Series II and D300E Series II Articulated Trucks Power Train Selector and Pressure Control Valve
2002/08/19 Correction to Operation and Maintenance Manual , "Caterpillar Monitoring System" {7451, 7490}
216 and 232 Skid Steer Loaders 3024 Engine Supplement Electric Starting Motor - Remove and Install
D350E Series II and D400E Series II Articulated Trucks Power Train Transmission Mounting
120H and 135H Motor Graders Equipment Lowering with Engine Stopped
793C Off-Highway Truck Machine Systems Relief Valve (Fan Drive Oil Cooler) - Disassemble
14H Motor Grader 3176C Engine Supplement Hood - Remove
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0615 - FMI 03
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0615 - FMI 01
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0615 - FMI 04
793C Off-Highway Truck Machine Systems Relief Valve (Fan Drive Oil Cooler) - Remove
3524B Engine for Caterpillar Built Machines Fuel Filter Base - Remove and Install
216 and 232 Skid Steer Loaders 3024 Engine Supplement Fuel Filter Group - Remove and Install
3524B Engine for Caterpillar Built Machines Power Train Oil Cooler - Remove and Install