PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND POSSIBLY REMOVING 521-0747 IMU CABLE ASSEMBLIES FROM DEALER PART STOCK
[UEBE0466]
SERVICE EQUIPMENT AND SUPPLIES
PARTS STOCK, ORDERING & RETURN
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND POSSIBLY REMOVING 521-0747 IMU CABLE ASSEMBLIES FROM DEALER PART STOCK
UEBE0466-00
Show/hide table
| 12Mar2020 |
U-146
A-113
D-135
O-130
Show/hide table
| Parts stock action only | PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND POSSIBLY REMOVING 521-0747 IMU CABLE ASSEMBLIES FROM DEALER PART STOCK |
|
| 7750 | PI70802 |
|
Show/hide table
| NOTE: | AVSpare’s obligations under this Service Letter are subject to, and shall not apply in contravention of, the laws, rules, regulations, directives, ordinances, orders, or statutes of the United States, or of any other applicable jurisdiction, without recourse or liability with respect to AVSpare. |
| NOTE: | When submitting claim for Parts Stock Action, Use the appropriate 99Z as the s/n, the appropriate Service Letter Program Number as the Part number in the Part Causing Failure field, "7751" as the Group Number, "56" as the Description Code. |
Show/hide table
| NOTE: | The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your AVSpare product analyst. |
Show/hide table
Show/hide table
Show/hide table
Show/hide table
TERMINATION DATE |
| 30Jun2020 |
PROBLEM
Show/hide table
| The 521-0747 CH01 IMU Cable Assembly that connects the front IMU to the radiator bulkhead connector can be pinned incorrectly. The cable is only used on large mining truck models equipped with the Full Command arrangement. The incorrect pins could result in fault codes and damage to the IMU sensor. |
ACTION REQUIRED
Show/hide table
| Inspect all 521-0747 IMU Cable Assemblies in dealer parts stock for the correct part change level of -03 and up. Remove all cables in inventory which are change level -01 and -02. NOTE: There is no need to inspect cables which are already installed and running on machines, the failure mode is immediately apparent once installed. |
Show/hide table
 |
| Image1 |
SERVICE CLAIM ALLOWANCES
Show/hide table
| Submit one claim for all parts removed from dealer parts stock. |
PARTS DISPOSITION
Show/hide table
| Handle the parts in accordance with your Warranty Bulletin on warranty parts handling. |
Information System:
PRODUCT SUPPORT PROGRAM FOR REPLACING THE PARK BRAKE PISTON OR SLEEVE ON CERTAIN R2900 AND R2900G LOAD HAUL DUMP MACHINES
PRODUCT SUPPORT PROGRAM FOR REPLACING OIL COOLERS ON CERTAIN 793F, 795F AC, AND 797 OFF-HIGHWAY TRUCKS
PRODUCT SUPPORT PROGRAM FOR REPAIRING THE FUEL TANK ON CERTAIN 24 MOTOR GRADERS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE 460-6957 TUBE ASSEMBLY SUPPORT BRACKET IN THE WATER LINES GROUP ON CERTAIN 777E OFF-HIGHWAY TRUCKS
PRODUCT SUPPORT PROGRAM FOR REPLACING PL042 OR PL141 DEVICES WITH A PL243 OR PL131 ON CERTAIN CATERPILLAR PRODUCTS
PRODUCT SUPPORT PROGRAM FOR REPLACING A PL240 OR PL241 RADIO WITH A PL243 4G CELLULAR RADIO ON CERTAIN CATERPILLAR PRODUCTS
PRODUCT SUPPORT PROGRAM FOR INSTALLATION OF A DIODE ON CERTAIN 548, 558, AND 568 FORESTRY EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR ADDING HOSE GUARD TO THE LOWER TRANSMISSION HOSE ON CERTAIN 775G OFF-HIGHWAY TRUCKS
PRODUCT SUPPORT PROGRAM FOR INSTALLING DIESEL EXHAUST FLUID (DEF) SUPPLY HOSE INSULATION ON CERTAIN R1700 AND R2900 LOAD HAUL DUMP MACHINES
PRODUCT SUPPORT PROGRAM FOR REPLACING PL240B WITH A PL243 4G CELLULAR RADIO ON CERTAIN CATERPILLAR PRODUCTS
PRODUCT SUPPORT PROGRAM FOR REPLACING PL542 V1 TO PL542 V2 CELLULAR RADIO SYSTEMS ON CERTAIN CATERPILLAR PRODUCTS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE ENGINE SOFTWARE ON CERTAIN 777E, 777F, AND 777G OFF-HIGHWAY TRUCKS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE DEF INJECTOR ON CERTAIN CATERPILLAR PRODUCTS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND POSSIBLY REPLACING 5465409 SPEED SENSORS ON CERTAIN REMAN 20R7980 TRANSMISSIONS IN DEALER PARTS STOCK
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING 0T-0244 BOLT WITH 8S-4723 BOLT IN 4671742 SUSPENSION SEAT ON CERTAIN R1700 LOAD HAUL DUMP MACHINES
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STARTING MOTOR ON CERTAIN CCS9, CP54B, CP56B, CP68B, CP74B, CS54B, CS56B, CS64B, CS66B, CS68B, CS74B, CS76B, AND CS78B COMPACTORS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND POSSIBLY REMOVING THE 356-4199 PINION SHAFT FROM DEALER PART STOCK
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE AXLE OIL LEVEL ON CERTAIN VIBRATORY SOIL COMPACTORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE AIR INTAKE TUBE ASSEMBLY SUPPORTS AND MOUNTING HARDWARE ON CERTAIN 794 AC, 796 AC, AND 798 AC OFF-HIGHWAY TRUCKS
PRODUCT SUPPORT PROGRAM FOR REPLACING CERTAIN LIFTER COVER ASSEMBLIES ON CERTAIN 797F OFF-HIGHWAY TRUCKS
PRODUCT SUPPORT PROGRAM FOR TIGHTENING OR REPLACING MISSING VALVE MOUNTING BOLTS ON THE HOIST VALVE MOUNTING BRACKET OF CERTAIN 785,789, AND 793 OFF-HIGHWAY TRUCKS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND POSSIBLY REPLACING THE REAR AXLE PINION SHAFT ON CERTAIN 980L, 980M, AND 982M WHEEL LOADERS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE BACKUP ALARM ON CERTAIN VIBRATORY SOIL COMPACTORS
PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING NEW SOFTWARE FOR THE ENGINE AND TRANSMISSION ECMS ON CERTAIN PM620 COLD PLANERS