938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train Oscillating Axle Housing Caterpillar


Oscillating Axle Housing
`



Illustration 1g00274928

(1) Torque for the 22 bolts ... 300 ± 40 N·m (220 ± 30 lb ft)

(2) Torque for the 22 bolts ... 300 ± 40 N·m (220 ± 30 lb ft)

(3) Torque for the plug ... 45 ± 6 N·m (33 ± 4 lb ft)

(4) At assembly, rubber toric seals and all surfaces that contact rubber toric seals must be clean and dry. Immediately before installation, apply a thin coat of oil on the surfaces of the metal seals that contact the rubber toric seals. The seal must be assembled square with the bore. Rubber toric seals must not have bulges or twists.

(5) Torque for the gauge assembly ... 45 ± 6 N·m (33 ± 4 lb ft)

(6) Refer to Testing and Adjusting, SENR6785, "Axle Housing and Bearing Preload - Adjust".

(7) Torque for the four bolts ... 570 ± 80 N·m (420 ± 60 lb ft)




Illustration 2g00274933

Detail A




Illustration 3g00274934

Detail B

(8) Outside diameter of the pinion housing ... 165.07 ± 0.08 mm (6.499 ± .003 inch)

(9) Sleeve Bearing

Inside diameter of the sleeve bearing ... 165.94 ± 0.13 mm (6.533 ± .005 inch)
Outside diameter of the sleeve bearing ... 181.46 ± 0.13 mm (7.144 ± .005 inch)

(10) Inside diameter of the trunnion support ... 180.98 ± 0.05 mm (7.125 ± .002 inch)




Illustration 4g00274935

Detail C

(11) Outside diameter of the trunnion ... 126.80 ± 0.08 mm (4.992 ± .003 inch)

(12) Sleeve Bearing

Inside diameter of the sleeve bearing ... 127.80 ± 0.10 mm (5.031 ± .004 inch)
Outside diameter of the sleeve bearing ... 140.20 ± 0.10 mm (5.520 ± .004 inch)

(13) Inside diameter of the trunnion support ... 139.75 ± 0.05 mm (5.502 ± .002 inch)




Illustration 5g00274936

(14) Torque for the six bolts ... 300 ± 40 N·m (220 ± 30 lb ft)

(15) Torque for the 12 bolts ... 300 ± 40 N·m (220 ± 30 lb ft)

(16) Torque for the 10 bolts ... 300 ± 40 N·m (220 ± 30 lb ft)

(17) Torque for the eight axle mounting bolts ... 1000 ± 125 N·m (740 ± 90 lb ft)




Illustration 6g00918726

(18) Torque for the two air purge screws ... 11 ± 4 N·m (8 ± 3 lb ft)

(19) Torque for the pressure relief fitting ... 13 ± 4 N·m (10 ± 3 lb ft)

Reference: For more information about this topic, refer to Specifications, System Operation, Testing and Adjusting, SENR6719, "938G Wheel Loader and IT38G Integrated Toolcarrier Traction Control System".

Information System:

938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System Piston Pump (Hydraulic Fan)
574B Forwarder Hydraulic System Boom Tilt Cylinder and Gate Cylinder (Horizontal) Pressure - Test and Adjust
3054E Industrial Engine Gear Group (Front)
14H Motor Grader 3176C Engine Supplement Air Compressor - Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Turbocharger - Disassemble
IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader MID 081 - CID 0070 - FMI 04
3054E Industrial Engine Front Housing and Covers
IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader MID 081 - CID 0070 - FMI 03
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System Pilot Valve (Joystick)
3524B Engine for Caterpillar Built Machines Fuel Transfer Pump - Assemble
C9 Engine For Caterpillar Built Machines Engine Oil Pump - Remove
14H Motor Grader 3176C Engine Supplement Air Compressor - Remove
247 and 257 Multi Terrain Loaders Power Train Piston Motor (Hydrostatic) - Remove
IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader MID 081 - CID 0248 - FMI 12
CB-534D and CB-564D Asphalt Compactors Cooling System Water Temperature Regulator - Replace
574B Forwarder Hydraulic System Grapple Cylinder Pressure - Test and Adjust
2002/11/04 A New Control Valve Improves the Service Life of the Transmission {3073}
IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader MID 081 - CID 0367 - FMI 02
574B Forwarder Hydraulic System Extendable Stick Cylinder Pressure - Test and Adjust
IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader MID 081 - CID 0368 - FMI 03
574B Forwarder Hydraulic System Combination Valve (Ladder) - Test and Adjust
R1600G Load Haul Dump Hydraulic System Lift Arm Positioner - Adjust
R1600 Load Haul Dump Hydraulic System Ride Control Accumulator - Test and Charge
14H Motor Grader 3176C Engine Supplement Radiator Guard and Support, Aftercooler, and Radiator - Remove