776D, 777D and 777D HAA Off-Highway Truck/Tractors Power Train Hydraulic Tank (Torque Converter, Hoist, Brake, and Transmission) Caterpillar


Hydraulic Tank (Torque Converter, Hoist, Brake, and Transmission)
`
776D, 777D and 777D HAA Off-Highway Truck/Tractors Power Train [SENR6912]
HYDRAULIC SYSTEM
TANK GP
776D, 777D and 777D HAA Off-Highway Truck/Tractors Power Train Hydraulic Tank (Torque Converter, Pulled Unit, Brake, and Transmission)
776D, 777D and 777D HAA Off-Highway Truck/Tractors Power Train Hydraulic Tank (Torque Converter, Hoist, Brake, and Transmission)



Illustration 1g00916396

Front view of torque converter, hoist, brake, and transmission hydraulic tank

(1) Torque converter, hoist, and brake section

(2) Transmission section

(3) Control valve




Illustration 2g00916398

View A-A

(4) Rear brake cooling relief valve

The hydraulic tank (torque converter, hoist, brake, and transmission) has two separate oil tanks. The torque converter, hoist, and brake section (1) is separated from the transmission section (2) by a wall inside the hydraulic tank. The transmission section (2) is smaller than the torque converter, hoist, and brake section (1) and provides oil for the transmission. The torque converter, hoist, and brake section (1) is larger than the transmission section (2) and provides oil for torque converter operation, hoist operation, and brake operation and cooling. The hydraulic tank is mounted to the left side of the frame.

A relief valve for rear brake cooling (4) is located inside the torque converter, hoist, and brake section (1). The relief valve for rear brake cooling (4) provides hydraulic pressure relief to the rear brake coolers. Torque converter, hoist, and brake section (1) also contains control valve (3) for the hoist cylinders.

Both transmission section (2) and torque converter, hoist, and brake section (1) are vented to breathers. Breathers for the torque converter, hoist, and brake section (1), the oil pump drive, and the torque converter are located on the right side of the horizontal frame member above the torque converter. The transmission breather is located on top of transmission section (2).




Illustration 3g00911334

Rear view of torque converter, hoist, brake, and transmission hydraulic tank

(1) Hydraulic tank for torque converter, hoist, and brake operation and cooling

(2) Hydraulic tank for transmission

(6) Return port for transmission scavenge pump

(7) Drain port for the lip seal case of the parking brake

(8) Drain port for AETA (an attachment)

(9) Drain port for parking and secondary brake valve

(10) Return port for brake makeup oil tank

(11) Return port for rear brake cooling oil (left brake)

(12) Return port for rear brake cooling oil (right brake)

(13) Return port for front brake cooling oil (an attachment)

(14) Suction port for transmission oil

(15) Suction port for hoist pump

(16) Outlet port to head end of hoist cylinders

(17) Suction port for torque converter charging section of the oil pump and parking brake release section of the oil pump

(18) Outlet port to rod end of hoist cylinders

(19) Outlet port to rear brake cooling system

(20) Inlet port to control valve (from pump)

(21) Return port for torque converter inlet relief valve

(22) Return port for torque converter scavenge pump

Information System:

R2900 Load Haul Dump Autodig System - If Equipped
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Pump - Remove
R2900 Load Haul Dump Joystick Control
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Main Control Valve
Air Conditioning and Heating R-12 All Caterpillar Machines Refrigerant Orifice Tube - Remove and Install
Air Conditioning and Heating R-12 All Caterpillar Machines Receiver-Dryer - Remove and Install
Air Conditioning and Heating R-12 All Caterpillar Machines Refrigerant Compressor - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Trunnion - Remove and Install
Air Conditioning and Heating R-12 All Caterpillar Machines General Information
2002/09/16 New Pins for the Bulldozer Blade are Now Greased {6061, 6065, 6066}
2003/04/21 A Sight Gauge for the Transmission Oil Level and an Oil Filler Tube at Ground Level are Available {3030}
Air Conditioning and Heating R-12 All Caterpillar Machines Machine Preparation for Disassembly and Assembly
120H and 135H Motor Graders Machine Systems Air Control Valve (Parking Brake) - Assemble
776D, 777D and 777D HAA Off-Highway Truck/Tractors Power Train Transmission Control
2002/11/18 New High Pressure Oil Hose Assembly Offers Added Flexibility for Thermal Expansion {1714, 7554}
2002/09/02 New Tachometers Provide Increased Service Life {7462}
776D, 777D and 777D HAA Off-Highway Truck/Tractors Power Train Pressure Switch (Service Brake and Retarder)
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Window Wiper and Wiper Motor
554 and 574 Forwarders Power Train Power Train Charge System Pressure - Test - 574 Forwarder (1FM434-UP)
226 and 242 Skid Steer LoadersEngine Supplement Engine - Install
R2900 Load Haul Dump Bucket Control Group Safety Pins
R2900 Load Haul Dump Walk-Around Inspection
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Pump - Install
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System Kickout System - Integrated Toolcarriers