AccuGrade Laser (CB420) Module - Flash Program Caterpillar


Module - Flash Program
`
1.1. Flash Program
2.1. Components (AccuGrade - Grade Control System) Flash Program

Flash Program

Perform the following procedure in order to flash program the ECM. The ECM is flashed in order to upgrade the software. The new software will allow the ECM to communicate with the AccuGrade - Grade Control System. The AVSpare Electronic Technician (Cat ET) contains the program WinFlash. WinFlash is used in order to load software into the ECM. The following procedure is used in order to FLASH software into the ECM.

  1. Procedure

    1. Connect the 196-0055 Data Link Cable between the 171-4400 Communication Adapter or the 275-5120 Communication Adapter and the Cat ET.

    1. Connect the 207-6845 Data Link Cable between the 171-4400 Communication Adapter and the diagnostic connector of the machine.

      Table 1
      Software    
      Part Number     Component    
      297-0153     Electric Mast    
      297-0154     LR400 Receiver    
      292-1268     LR410 Receiver    
      302-4509     Display    
      296-2868     Angle Sensor    
      284-5170     Rotation Sensor    
      305-7418     Grade Slope Control    

    1. Use WinFlash in order to load the software. Refer to Table 1 for the part number of the software.

Note: Flash programming is NOT allowed if the engine is running, or the machine is moving.

Components (AccuGrade - Grade Control System) Flash Program

Perform the following procedure in order to flash program the system components. The system components are flashed in order to upgrade the software. The new software will allow the system components to communicate with the ECM and each other. The Cat ET contains the program WinFlash. WinFlash is used in order to load software into the system components. The following procedure is used in order to FLASH software into the system components.


NOTICE

Do not stop the process. The ECM will be damaged and need to be replaced.


  1. Procedure

    1. Connect the 196-0055 Data Link Cable between the 171-4400 Communication Adapter or the 275-5120 Communication Adapter and the Cat ET.

    1. Connect the 207-6845 Data Link Cable between the 171-4400 Communication Adapter and the diagnostic connector of the machine.

    1. Use WinFlash in order to load the software. Refer to Table 1 for the part number of the software.

Note: Flash programming is NOT allowed if the engine is running, or the machine is moving.

Information System:

16M Motor Grader Power Train Drive Chain - Remove
AccuGrade</SUP> Laser (CB420) Full Sensor - Calibrate
16M Motor Grader Power Train Drive Chain - Install
16M Motor Grader Power Train Wheel and Tire (Rear) - Remove and Install
24M Motor Grader Hydraulic and Steering System Pump Control Valve (Implement, Steering)
587R Pipelayer Power Train Transmission Hydraulic Control Valve - Remove
770 and 772 Off-Highway Truck/Tractors Metering Pump (Steering) - Remove and Install
0R-9393 Cylinder Pack Gp Piston Ring Position on Certain C16, 3406E, and 3456 Engines{1215, 1225}
584 and 584HD Forwarders Slope Operation
24M Motor Grader Hydraulic and Steering System Piston Pump (Implement and Steering)
16M Motor Grader Machine Systems Piston Pump (Hydraulic Fan) - Assemble
EquipmentManager User Guide Getting Started
Problems with Bias Ply Tires on Specific Off-Highway Trucks{4203}
541 Track Feller Buncher, 551 Track Feller Buncher and 552 Track Feller Buncher Machine Systems Pilot Hydraulic System
R1600G Load Haul Dump Cooling System Coolant Additive (DEAC) - Add
541 Track Feller Buncher, 551 Track Feller Buncher and 552 Track Feller Buncher Machine Systems Pump Flow - Test
Cleaning the Compression Brake{1129}
216B2, 226B2, 232B2, 236B2, 242B2 and 252B2 Skid Steer Loaders Plate Locations and Film Locations
216B2, 226B2, 232B2, 236B2, 242B2 and 252B2 Skid Steer Loaders Engine Starting
216B2, 226B2, 232B2, 236B2, 242B2 and 252B2 Skid Steer Loaders Operation Information
216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders, 247B3 and 257B3 Multi Terrain Loaders and 259B3 Compact Track Loader Cooling System Coolant Extender (ELC) - Add
216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders, 247B3 and 257B3 Multi Terrain Loaders and 259B3 Compact Track Loader Cooling System Level - Check
Inspection and Salvage of Rear Wheel Spindles for Certain Off-Highway Trucks {4201, 4205}
770 and 772 Off-Highway Truck Hydraulic and Braking System Brake System Air - Purge