Customer Specified Parameters Table
`
C4.4 and C6.6 Engines for Caterpillar Built Machines
[KENR5389]
C4.4 and C6.6 Engines for Caterpillar Built Machines
Customer Specified Parameters
C4.4 and C6.6 Engines for Caterpillar Built Machines
Can Not Reach Top Engine RPM
ELECTRICAL AND STARTING SYSTEM
ELECTRONICS GP-ENGINE
C4.4 and C6.6 Engines for Caterpillar Built Machines
Replacing the ECM
C4.4 and C6.6 Engines for Caterpillar Built Machines
Flash Programming
C4.4 and C6.6 Engines for Caterpillar Built Machines
Electronic Service Tool Will Not Communicate with ECM
C4.4 and C6.6 Engines for Caterpillar Built Machines
Test ECM Mode
Show/hide table
Customer Specified Parameters | ||
---|---|---|
ECM Parameter | Possible Values | Default Value |
Engine Rating Parameter | ||
"Rating Number" | 1 to 4 | 1 |
Low/High Idle Parameters | ||
"Low Idle Speed" | 700 to 1200 rpm | 1200 rpm |
"High Idle Speed" | 1900 to 2900 rpm | 2310 rpm |
ECM Identification Parameter | ||
"Equipment ID" | 17 Digits
Available characters are dependent on the service tool that is used |
Not Programmed |
PTO and Throttle Lock Parameters | ||
"Throttle Lock Feature Installation Status" | Installed
Not Installed |
Not Installed |
"PTO Engine Speed Setting" | 0 to 3000 rpm | Not Installed |
"Throttle Lock Increment Speed Ramp Rate" | 0 to 600 rpm/sec | Not Installed |
"Throttle Lock Engine Set Speed Increment" | 0 to 200 rpm | Not Installed |
Miscellaneous | ||
"Monitoring Mode Shutdowns" | Disabled
Enabled |
Disabled |
"Monitoring Mode Derates" | Disabled
Enabled |
Enabled |
"Limp Home Desired Engine Speed" | 700 to 1800 rpm | 1200 rpm |
J1939 Continuous Fault Handling | ||
"Remote Torque Speed Control Enable Status" | Disabled
Enabled |
Disabled |
Configurable Inputs | ||
"Coolant Level Sensor" | Not Installed
Installed |
Not Installed |
"Air Filter Restriction Switch Installation Status" | Not Installed
Installed |
Not Installed |
"Fuel/Water Separator Switch Installation Status" | Not Installed
Installed |
Not Installed |
"User Defined Switch Installation Status" | Not Installed
Installed |
Not Installed |
Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines
Governor - Adjust
C4.4 and C6.6 Engines for Caterpillar Built Machines
Customer Specified Parameters
C4.4 Industrial Engine
Fuel Related Components in Cold Weather
C4.4 and C6.6 Engines for Caterpillar Built Machines
Multiposition Switch Setup
R1700G Load Haul Dump
Safety Messages
R2900G Load Haul Dump
Caterpillar Monitoring System
AP655D and BG655D Asphalt Pavers Propel System
Pressure Limiter Valve - Test and Adjust - Left Propel Pump (Steel Track)
False Warning for Low Transmission Oil Level on Some Off-Highway Trucks{3101, 7422}
3412E Engine for Caterpillar Built Machines
Coolant Temperature Is High
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train
Idler Axle - Remove
770 and 772 Off-Highway Truck/Tractors
Heater Coil - Remove and Install
587R Pipelayer Machine Systems
Platform - Install
C4.4 and C6.6 Engines for Caterpillar Built Machines
Can Not Reach Top Engine RPM
3412E Engine for Caterpillar Built Machines
Engine Misfires, Runs Rough or Is Unstable
EquipmentManager Dealer Administrator Manual
Manage Event Tracking
EquipmentManager Dealer Administrator Manual
Upload Data
EquipmentManager Dealer Administrator Manual
Manage Planned Maintenance
3408E and 3412E Engines for Caterpillar Built Machines
Engine Overspeeds on Start-up
EquipmentManager Dealer Administrator Manual
Preferences
EquipmentManager User Guide
Asset Watch
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System
Pilot Valve
C15 and C18 Generator Set Engines
Radiator Bottom Tank - Remove and Install - Jacket Water Heater
C15 and C18 Generator Set Engines
Radiator Top Tank - Remove and Install - Jacket Water Heater
587R Pipelayer Machine Systems
Hydraulic Tank and Filter - Remove