R1600G Load Haul Dump Remote Control System Machine Preparation for Troubleshooting Caterpillar


Machine Preparation for Troubleshooting
`
R1600G Load Haul Dump Remote Control System [KENR8506]
REMOTE CONTROL SYSTEM
R1600G Load Haul Dump Remote Control System Machine Preparation for Troubleshooting

------ WARNING! ------

Sudden movement of the machine or release of oil under pressure can cause serious injury to persons on or near the machine.

To prevent possible injury, perform the procedure that follows before testing and adjusting the hydraulic system.

----------------------

------ WARNING! ------

Personal injury or death can result from escaping fluid under pressure.

Escaping fluid under pressure, even a very small pin-hole size leak, can penetrate body tissue and cause serious injury and possible death. If fluid is injected into your skin, it must be treated by a doctor familiar with this type of injury.

Always use a board or cardboard when checking for a leak.

----------------------


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on AVSpare products.

Dispose of all fluids according to local regulations and mandates.


Note: Permit only one operator on the machine. Keep all other personnel away from the machine or in the operator's sight.

  1. Move the machine to a smooth, horizontal location that is away from operating machines and away from personnel. Lower the work tool to the ground.

  1. Place the transmission direction and speed control in the NEUTRAL position and in any speed position. Engage the steering and transmission lock lever.

  1. Engage the parking brake. Place wheel blocks in front of the wheels and behind the wheels.

  1. Stop the engine.

  1. Install the steering frame lock.

  1. Move the joystick control lever through the full range of travel. This will relieve any pressure that may be present in the implement hydraulic system. Place the joystick control lever in the HOLD position.

  1. Move the steering control several times in both directions to release the pressure in the steering system.

  1. Depress the brake pedal repeatedly. This will relieve any pressure that may be present in the braking system.

  1. Depress the breaker relief valve on the hydraulic tank to release the pressure in the hydraulic tank.

Information System:

R1600G Load Haul Dump Remote Control System Control Valve (Steering and Bucket)
R1600G Load Haul Dump Remote Control System General Information
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Control Valve (Auxiliary)
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Control Valve (Lift)
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Control Valve (Tilt)
3408E and 3412E Engines for Caterpillar Built Machines Cooling Fan Control - Test
587R Pipelayer Machine Systems Boom - Remove and Install
3412E Engine for Caterpillar Built Machines Coolant Flow - Test
Reworking the Pressure Sensor for the Saw Pump{1408, 5057, 6543}
CB14 Paving Compactor Machine Systems Piston Pump (Propel) - Assemble
CB14 Paving Compactor Machine Systems Piston Pump (Propel) - Disassemble
The Fitting on the Air Cleaner Group is Installed Incorrectly on Specific Off-Highway Trucks{1051}
3412E Engine for Caterpillar Built Machines Cooling Fan Speed - Test
587R Pipelayer Machine Systems Main Control Valve - Remove
587R Pipelayer Machine Systems Main Control Valve - Install
EquipmentManager Dealer Administrator Manual Fault Codes
24M Motor Grader Power Train Transmission Hydraulic Control
587R Pipelayer Machine Systems Main Control Valve - Disassemble
3412E Engine for Caterpillar Built Machines Electrical Power Supply - Test
587R Pipelayer Machine Systems Main Control Valve - Assemble
24M Motor Grader Hydraulic and Steering System Implement System
R1600G Load Haul Dump Power Train Machine Preparation for Troubleshooting
R1600G Load Haul Dump Steering System Steering System Troubleshooting
R1600G Load Haul Dump Steering System System Pressure - Release