Component Location
`
C18 Engine for Caterpillar Built Machines
[KENR5447]
C18 Engine for Caterpillar Built Machines
Electronic Service Tools
C18 Engine for Caterpillar Built Machines
Diagnostic Trouble Code List
ELECTRICAL AND STARTING SYSTEM
1.1. C18 Engine
Show/hide table
![]() | |
Illustration 1 | g01394000 |
Diagram of components |
C18 Engine
Show/hide table
![]() | |
Illustration 2 | g01394001 |
Left side engine view (typical example) (1) Primary engine speed/timing sensor (2) Engine coolant temperature sensor (3) Secondary engine speed/timing sensor (4) Intake manifold pressure sensor (5) Atmospheric pressure sensor (6) Injector valve cover entry connector (7) Engine oil pressure sensor (8) Intake manifold air temperature sensor (9) Timing calibration probe connector (10) J2/P2 ECM connector (11) J1 ECM connector (12) Engine Control Module (ECM) |
Show/hide table
![]() | |
Illustration 3 | g01394003 |
Location of the components on the fuel filter base (13) Differential pressure switch (fuel) (14) Fuel pressure sensor (15) Fuel temperature sensor |
Show/hide table
![]() | |
Illustration 4 | g01195919 |
Location of the right turbocharger inlet pressure sensor (typical example) |
Information System:
C4.4 and C6.6 Engines for Caterpillar Built Machines
E360 Low Engine Oil Pressure
C4.4 and C6.6 Engines for Caterpillar Built Machines
Event Codes
R1600G Load Haul Dump Power Train
Output Transfer Gears - Adjust
R1600G Load Haul Dump Steering System
Articulated Hitch
R1600G Load Haul Dump Machine Electrical System
Circuit Breaker
R1600G Load Haul Dump Power Train
Torque Converter and Updrive
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System
Ride Control Valve (2-Function, 3-Function Control Valve)
587R Pipelayer Machine Systems
Pilot Control Valve - Install - Load, Boom and Counterweight
587R Pipelayer Machine Systems
Pilot Control Valve - Remove - Load, Boom, and Counterweight
Bench Test Procedure for a 14L, 120M, 120M Series 2, 12M, 12M Series 2, 12M Series 3, 140M, 140M Series 2, 140M Series 3, 160M, 160M Series 2, and 160M Series 3 Motor Grader Transmission {3030, 3073}
120K Motor Grader
Capacities (Refill)
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System
Relief Valve (Line)
R1600G Load Haul Dump Power Train
Differential Pinion Preload - Adjust
R1600G Load Haul Dump Power Train
Differential Backlash and Bearings - Adjust
R1600G Load Haul Dump Braking System
Brake Release System
R1600G Load Haul Dump Braking System
General Information
R1600G Load Haul Dump Braking System
Service and Parking Brake System
C4.4 and C6.6 Engines for Caterpillar Built Machines
E361 High Engine Coolant Temperature
C4.4 and C6.6 Engines for Caterpillar Built Machines
E539 High Intake Manifold Air Temperature
160M and 160 Motor Grader Machine Systems
Bank Valve - Install - Rear Frame
3412E Engine for Caterpillar Built Machines
Injection Actuation Pressure Control Valve - Test
C4.4 and C6.6 Engines for Caterpillar Built Machines
5 Volt Sensor Supply Circuit - Test
140M and 150 Motor Grader Power Train
Transmission - Assemble
216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders, 247B3 and 257B3 Multi Terrain Loaders and 259B3 Compact Track Loader
Sprocket - Inspect