938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0263 - FMI 00 Caterpillar


MID 028 - CID 0263 - FMI 00
`
938G Wheel Loader, 938G Series II <BR>Wheel Loader, IT38G <BR>Integrated Toolcarrier and IT38G Series II <BR>Integrated Toolcarrier Traction Control System [SENR6719]
ELECTRICAL AND STARTING SYSTEM
ELECTRONICS GP-MACHINE

Conditions Which Generate This Code:

Note: This procedure can cause new diagnostic codes to be recorded. Ignore these newly created diagnostic codes. Complete this procedure and then clear the diagnostic codes that were created during this procedure.

This failure is recorded when the ECM reads the voltage of the sensor supply circuit and the voltage is above normal.

Test Step 1. CHECK FOR THE CORRECT VOLTAGE AT THE ELECTRONIC CONTROL MODULE.

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. At the machine harness connector J2 of the ECM for the traction control, measure the voltage between contact J2-9 (wire 709-OR) and frame ground. Use the 7X-1710 Cable probes to measure the voltage. Do NOT disconnect the machine harness from the ECM for the traction control.

  1. The voltage is 10.0 ± 0.6 DCV.

Expected Result:

Results:

  • OK - The voltage is 10.0 ± 0.6 DCV. The sensor supply voltage is correct. Verify that the diagnostic code is still active on the message center. If the diagnostic code is still present, the ECM for the traction control has failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace".

    Stop.

  • NOT OK - The voltage is greater than 10.0 ± 0.6 DCV. The sensor supply voltage is NOT correct. Proceed to test step 2.

Test Step 2. CHECK THE HARNESS FOR A SHORT TO THE + BATTERY CIRCUIT.

  1. Turn the disconnect switch and the key start switch to the OFF position.

  1. Disconnect the machine harness connector J1 and J2 from the ECM for the traction control.

  1. At the machine harness connector J2 of the ECM for the traction control, measure the resistance from contact J2-9 (wire 709-OR) to contact J1-1 (+ battery).

Expected Result:

The resistance is greater than 5000 ohms.

Results:

  • OK - The resistance is greater than 5000 ohms. The resistance is correct. The ECM for the traction control has failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace".

    Stop.

  • NOT OK - The resistance is not greater than 5000 ohms. The harness has failed. The machine harness is shorted to the + battery.

    Repair: Repair the machine harness or replace the machine harness.

    Stop.

Information System:

814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Machine Systems Instrument Panel (Side) - Remove
226 and 242 Skid Steer Loaders Power Train Piston Motor (Hydrostatic) - Remove
226 and 242 Skid Steer Loaders Power Train Piston Pump (Hydrostatic) - Install
RM-350B Road Reclaimer/Soil Stabilizer Machine Systems Position Sensor (Front Steering) - Remove and Install
3512 and 3516 EUI Engines for Caterpillar Built Machines Air Inlet and Exhaust System Operation
2002/08/19 2002A Service Pack 1 for Caterpillar Electronic Technician (Cat ET) is Now Available {0785}
2002/08/01 2002A Service Pack 1 for Caterpillar Electronic Technician (Cat ET) is now available {0785}
226 and 242 Skid Steer Loaders Power Train Piston Pump (Hydrostatic) - Remove
D350E Series II and D400E Series II Articulated Trucks Power Train Torque Converter
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Inspect
814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Machine Systems Steering Control Valve - Assemble
814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Machine Systems Steering Control Valve - Disassemble
814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Machine Systems Instrument Panel (Side) - Install
814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Machine Systems Evaporator Coil - Remove and Install
814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Machine Systems Heater Coil - Remove and Install
938G Wheel Loader, 938G Series II <BR>Wheel Loader, IT38G <BR>Integrated Toolcarrier and IT38G Series II <BR>Integrated Toolcarrier Traction Control System MID 028 - CID 0263 - FMI 01
3508B Engine for D11R Track-Type Tractors Engine Cooling Fan Bypass Solenoid
PS-360B Paving Compactor Fuses - Replace
2002/08/12 Correction to Disassembly and Assembly , "Differential and Bevel Gear - Assemble" {3256, 3258}
D350E Series II and D400E Series II Articulated Trucks Power Train Relief Valve (Torque Converter Outlet)
226 and 242 Skid Steer Loaders Power Train Piston Motor (Hydrostatic) - Install
938G Wheel Loader, 938G Series II <BR>Wheel Loader, IT38G <BR>Integrated Toolcarrier and IT38G Series II <BR>Integrated Toolcarrier Traction Control System MID 028 - CID 0296 - FMI 09
R1600G Load Haul Dump Hydraulic System Lift and Tilt Cylinder Drift - Check
R1600G Load Haul Dump Hydraulic System Lift and Tilt Cylinder Speed - Check