938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0609 - FMI 03 Caterpillar


MID 028 - CID 0609 - FMI 03
`

Conditions Which Generate This Code:




Illustration 1g00913287

This is a mini schematic of the Proportional Solenoids for the Brake.

This diagnostic code is associated with the Proportional Solenoid for the Left Front Brake. The FMI 03 means that the ECM has determined that the voltage of the solenoid circuit is above normal.

The possible causes of the diagnostic code are listed:

  • The solenoid has failed.

  • The energize circuit of the solenoid is shorted to the + battery circuit.

  • The ECM has failed. This is unlikely.

Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0609 FMI 03 is active before performing this procedure.

Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.

System Response:

The diagnostic code of CID 0609 FMI 03 will be logged in the internal memory of the ECM.

The traction control system is inoperable.

Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE + BATTERY CIRCUIT.

  1. Turn the key start switch and the disconnect switch to the OFF position.

  1. Disconnect the machine harness connectors from the solenoid and the ECM.

  1. At the machine harness connector for the ECM, measure the resistance from contact J1-10 (wire E923-PK) to all contacts that are used in the machine harness for the ECM.

Expected Result:

Each resistance measurement is greater than 5000 ohms.

Results:

  • OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 2.

  • NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J1-10 (E923-PK) and the circuit that has a low resistance measurement.

    Repair: Repair the machine harness or replace the machine harness.

    Stop.

Test Step 2. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE.

  1. Inspect the contacts and clean the contacts of the harness connectors.

  1. Reconnect all harness connectors.

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Operate the machine.

  1. Determine if the CID 0609 FMI 03 is active.

Expected Result:

The CID 0609 FMI 03 is active.

Results:

  • YES - The CID 0609 FMI 03 is active. The problem has not been corrected. The ECM may have failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Troubleshooting, "Electronic Control Module (ECM) - Replace".

    Stop.

  • NO - The CID 0609 FMI 03 is not active. The problem does not exist at this time.

    Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.

    Stop.

Information System:

938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0608 - FMI 02
R2900 Load Haul Dump Plate Locations and Film Locations
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0607 - FMI 02
3524B Engine for Caterpillar Built Machines Engine Oil Pump - Install
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Hydraulic and Steering System Introduction
554 and 574 Forwarders Power Train Filling and Flushing the Hydrostatic System - Test
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0606 - FMI 02
IT62G Series II Integrated Toolcarrier and 950G Series II and 962G Series II Wheel Loaders Capacities (Refill)
D350E Series II and D400E Series II Articulated Trucks Power Train Priority Valve
3524B Engine for Caterpillar Built Machines Engine Oil Pump - Remove
Installation Procedure for the New Traction Control System{5051}
R1600 Load Haul Dump Machine Electrical System Transmission Oil Temperature
226 and 242 Skid Steer Loaders Power Train Chain (Drive) - Install
226 and 242 Skid Steer Loaders Power Train Chain (Drive) Tension - Adjust
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Hydraulic and Steering System Piston Pump (Hydraulic and Steering)
Field Installation Of 3Z-5855 Jake Brake Modification {1119, 1129, 7314}
TK711, TK721, TK722 and TK732 Track Feller Bunchers Safety Messages
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0609 - FMI 05
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0609 - FMI 06
TK711, TK721, TK722 and TK732 Track Feller Bunchers Additional Messages
D350E Series II and D400E Series II Articulated Trucks Power Train Transmission Hydraulic Control
PMG3516 Power Module Roading
R2900 Load Haul Dump Battery Disconnect Switch
TK711, TK721, TK722 and TK732 Track Feller Bunchers Specifications