938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0612 - FMI 06 Caterpillar


MID 028 - CID 0612 - FMI 06
`

Conditions Which Generate This Code:




Illustration 1g00913287

This is a mini schematic of the Proportional Solenoids for the Break.

This diagnostic code is associated with the Proportional Solenoid for the Right Rear Brake. The FMI 06 means that the ECM has determined that the current of the solenoid is above normal.

The possible causes of this diagnostic code are listed:

  • The energize circuit of the solenoid is shorted to ground.

  • The solenoid has failed.

  • The ECM has failed. This is unlikely.

Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0612 FMI 06 is active before performing this procedure.

Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.

System Response:

The diagnostic code of CID 0612 FMI 06 will be logged in the internal memory of the ECM.

The traction control system is inoperable.

Test Step 1. CHECK THE SOLENOID.

  1. Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.

  1. Observe the status of the diagnostic code.

  1. Disconnect the solenoid with the active diagnostic code from the machine harness.

Expected Result:

CID 0612 FMI 06 changes to CID 0612 FMI 05 when the solenoid is disconnected.

Results:

  • YES - CID 0612 FMI 06 changes to CID 0612 FMI 05 when the solenoid is disconnected. The circuit is correct.

    Repair: The solenoid has failed. Repeat this test "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid.

    Stop.

  • NO - CID 0612 FMI 06 remains active. Proceed to Test Step 2.

Test Step 2. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND.

  1. Turn the key start switch and the disconnect switch to the OFF position.

  1. The solenoid remains disconnected from the machine harness.

  1. Disconnect the machine harness connector(s) from the ECM.

  1. At the machine harness connector, measure the resistance from the signal contact J1-11 (wire E926-BU) to all contacts that are used in the machine harness for the ECM.

Expected Result:

Each resistance measurement is greater than 5000 ohms.

Results:

  • OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.

  • NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J1-11 (wire E926-BU) and the circuit with the low resistance measurement.

    Repair: Repair the machine harness or replace the machine harness.

    Stop.

Test Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.

  1. Inspect the harness connectors and clean the contacts of the harness connectors.

  1. Reconnect all harness connectors.

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Operate the machine.

  1. Check the status of the CID 0612 FMI 06.

Expected Result:

The CID 0612 FMI 06 is active.

Results:

  • YES - The CID 0612 FMI 06 is active. The diagnostic code has not been corrected. The ECM may have failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Troubleshooting, "Electronic Control Module (ECM) - Replace".

    Stop.

  • NO - The CID 0612 FMI 06 is not active. The diagnostic code does not exist at this time.

    Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.

    Stop.

Information System:

938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0612 - FMI 05
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0612 - FMI 03
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0611 - FMI 06
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0611 - FMI 05
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0611 - FMI 03
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0610 - FMI 06
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0610 - FMI 05
797 Off-Highway Truck Engine Supplement Engine Oil Cooler - Remove
D250E Series II and D300E Series II Articulated Trucks Power Train Transmission Hydraulic Control
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0610 - FMI 03
R1600 Load Haul Dump Machine Electrical System Hydraulic Oil Temperature
R1600 Load Haul Dump Machine Electrical System Lift Arm Positioner
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train Clutch (Forward High and Forward Low)
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train Clutch (Reverse and Second)
3524B Engine for Caterpillar Built Machines Engine Oil Cooler - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train Clutch (First and Third)
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Air System and Brakes Monitoring System
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train Transmission Case
814F Wheel Dozer, 815F Soil Compactor and 816F Landfill CompactorEngine Supplement Engine, Torque Converter, Transmission and Output Transfer Gears - Remove
2002/08/19 Correction to Operation and Maintenance Manual , "Caterpillar Monitoring System" {7451, 7490}
2002/08/19 Correction to Operation and Maintenance Manual , "Caterpillar Monitoring System" {7451, 7490}
D250E Series II and D300E Series II Articulated Trucks Power Train Selector and Pressure Control Valve
3524B Engine for Caterpillar Built Machines Engine Oil Cooler - Disassemble
R2900 Load Haul Dump Engine Start Switch