938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0613 - FMI 03 Caterpillar


MID 028 - CID 0613 - FMI 03
`

Conditions Which Generate This Code:




Illustration 1g00913930

This is a mini schematic for the On/Off Pilot Solenoid.

This diagnostic code is associated with the On/Off Pilot Solenoid. The FMI 03 means that the ECM has determined that the voltage of the solenoid circuit is above normal.

The possible causes of the diagnostic code are listed:

  • The solenoid has failed.

  • The energize circuit of the solenoid is shorted to the + battery circuit.

  • The ECM has failed. This is unlikely.

Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0613 FMI 03 is active before performing this procedure.

Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.

System Response:

The diagnostic code of CID 0613 FMI 03 will be logged in the internal memory of the ECM.

The traction control system is inoperable.

Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE +BATTERY CIRCUIT.

  1. Turn the key start switch and the disconnect switch to the OFF position.

  1. Disconnect the machine harness connectors from the solenoid and the ECM.

  1. At the machine harness connector for the ECM, measure the resistance from contact J2-37 (wire E930-BU) to all contacts that are used in the machine harness connectors for the ECM.

Expected Result:

Each resistance measurement is greater than 5000 ohms.

Results:

  • OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 2.

  • NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J2-37 (E930-BU) and the circuit that has a low resistance measurement.

    Repair: Repair the machine harness or replace the machine harness.

    Stop.

Test Step 2. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE.

  1. Inspect the contacts and clean the contacts of the harness connectors.

  1. Reconnect all harness connectors.

  1. Turn the disconnect switch and the key start switch to the ON position.

  1. Operate the machine.

  1. Determine if the CID 0613 FMI 03 is active.

Expected Result:

The CID 0613 FMI 03 is active.

Results:

  • YES - The CID 0613 FMI 03 is active. The problem has not been corrected. The ECM may have failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Troubleshooting, "Electronic Control Module (ECM) - Replace".

    Stop.

  • NO - The CID 0613 FMI 03 is not active. The problem does not exist at this time.

    Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.

    Stop.

Information System:

143H and 163H Motor Graders All Wheel Drive Location of Electrical Components
R2900 Load Haul Dump Fire Suppression System (Foam) - If Equipped
R2900 Load Haul Dump Engine Start Switch
3524B Engine for Caterpillar Built Machines Engine Oil Cooler - Disassemble
D250E Series II and D300E Series II Articulated Trucks Power Train Selector and Pressure Control Valve
2002/08/19 Correction to Operation and Maintenance Manual , "Caterpillar Monitoring System" {7451, 7490}
2002/08/19 Correction to Operation and Maintenance Manual , "Caterpillar Monitoring System" {7451, 7490}
814F Wheel Dozer, 815F Soil Compactor and 816F Landfill CompactorEngine Supplement Engine, Torque Converter, Transmission and Output Transfer Gears - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train Transmission Case
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Air System and Brakes Monitoring System
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train Clutch (First and Third)
3524B Engine for Caterpillar Built Machines Engine Oil Cooler - Install
3524B Engine for Caterpillar Built Machines Engine Oil Cooler - Assemble
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0613 - FMI 05
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0613 - FMI 06
216 and 232 Skid Steer Loaders 3024 Engine Supplement Alternator - Remove and Install
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0615 - FMI 00
Installation Procedure for New 190-3692 Pressure Sensor {1408, 3016}
216 and 232 Skid Steer Loaders 3024 Engine Supplement Electric Starting Motor - Remove and Install
D350E Series II and D400E Series II Articulated Trucks Power Train Transmission Mounting
120H and 135H Motor Graders Equipment Lowering with Engine Stopped
793C Off-Highway Truck Machine Systems Relief Valve (Fan Drive Oil Cooler) - Disassemble
14H Motor Grader 3176C Engine Supplement Hood - Remove
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System MID 028 - CID 0615 - FMI 03