IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader Diagnostic Code List Caterpillar


Diagnostic Code List
`

Table 1
Component Identifier (CID)
Power Train ECM (MID 081)    
For troubleshooting, see the procedure with the same diagnostic code.    
CID and FMI     Component    
CID 0041 Sensor Supply Voltage    
FMI 03     "Voltage above normal or shorted high"    
FMI 04     "Voltage below normal or shorted low"    
CID 0070 Limit Switch (Parking Brake)    
FMI 03     "Voltage above normal or shorted high"    
FMI 04     "Voltage below normal or shorted low"    
CID 0149 Solenoid (Ride Control)    
FMI 03     "Voltage above normal or shorted high"    
FMI 05     "Current below normal or open circuit"    
FMI 06     "Current above normal or grounded circuit"    
CID 0168 Electrical System Voltage    
FMI 00     "Data valid but above the normal operational range"    
FMI 01     "Data valid but below normal operational range"    
CID 0177 Temperature Sensor (Transmission Oil)    
FMI 03     "Voltage above normal or shorted high"    
FMI 04     "Voltage below normal or shorted low"    
CID 0190 Speed Signal (Engine)    
FMI 02     "Data erratic, intermittent, or incorrect"    
CID 0248 AVS Data Link    
FMI 12     "Bad device or component"    
CID 0363 Solenoid Valve (Ride Control)    
FMI 03     "Voltage above normal or shorted high"    
FMI 05     "Current below normal or open circuit"    
FMI 06     "Current above normal or grounded circuit"    
CID 0367 Rocker Switch (Ride Control)    
FMI 02     "Data erratic, intermittent, or incorrect"    
FMI 03     "Voltage above normal or shorted high"    
CID 0368 Transmission Auto/Manual Switch    
FMI 03     "Voltage above normal or shorted high"    
FMI 04     "Voltage below normal or shorted low"    
CID 0444 Magnetic Switch (Start Relay)    
FMI 03     "Voltage above normal or shorted high"    
FMI 05     "Current below normal or open circuit"    
FMI 06     "Current above normal or grounded circuit"    
CID 0585 Speed Sensor (Transmission Output 1)    
FMI 02     "Data erratic, intermittent, or incorrect"    
CID 0590 Electronic Control Module (Engine)    
FMI 09     "Abnormal Update"    
CID 0672 Speed Sensor (Torque Converter output)    
FMI 01     "Data valid but below normal operational range"    
CID 0673 Speed Sensor No. 2 (Transmission Output)    
FMI 02     "Data erratic, intermittent, or incorrect"    
CID 0674 Speed Sensor (No. 1) for Transmission Intermediate    
FMI 02     "Data erratic, intermittent, or incorrect"    
CID 0675 Speed Sensor No. 2 (Transmission Intermediate)    
FMI 02     "Data erratic, intermittent, or incorrect"    
CID 0793 Pressure Switch (Primary Steering Oil)    
FMI 03     "Voltage above normal or shorted high"    
FMI 04     "Voltage below normal or shorted low"    
CID 0794 Pressure Switch (Secondary Steering Oil)    
FMI 03     "Voltage above normal or shorted high"    
FMI 04     "Voltage below normal or shorted low"    
CID 0795 Relay (Secondary Steering)    
FMI 03     "Voltage above normal or shorted high"    
FMI 05     "Current below normal or open circuit"    
FMI 06     "Current above normal or grounded circuit"    
CID 1327 Position Sensor (Left Brake Pedal)    
FMI 03     "Voltage above normal or shorted high"    
FMI 04     "Voltage below normal or shorted low"    
FMI 13     "Out of calibration"    
CID 1401 Modulating Valve (No. 1) (Transmission)    
FMI 03     "Voltage above normal or shorted high"    
FMI 05     "Current below normal or open circuit"    
FMI 06     "Current above normal or grounded circuit"    
FMI 13     "Out of calibration"    
CID 1402 Modulating Valve (No. 2) (Transmission)    
FMI 03     "Voltage above normal or shorted high"    
FMI 05     "Current below normal or open circuit"    
FMI 06     "Current above normal or grounded circuit"    
FMI 13     "Out of calibration"    
CID 1403 Modulating Valve (No. 3) (Transmission)    
FMI 03     "Voltage above normal or shorted high"    
FMI 05     "Current below normal or open circuit"    
FMI 06     "Current above normal or grounded circuit"    
FMI 13     "Out of calibration"    
CID 1404 Modulating Valve (No. 4) (Transmission)    
FMI 03     "Voltage above normal or shorted high"    
FMI 05     "Current below normal or open circuit"    
FMI 06     "Current above normal or grounded circuit"    
FMI 13     "Out of calibration"    
CID 1405 Modulating Valve (No. 5) (Transmission)    
FMI 03     "Voltage above normal or shorted high"    
FMI 05     "Current below normal or open circuit"    
FMI 06     "Current above normal or grounded circuit"    
FMI 13     "Out of calibration"    
CID 1406 Modulating Valve (No. 6) (Transmission)    
FMI 03     "Voltage above normal or shorted high"    
FMI 05     "Current below normal or open circuit"    
FMI 06     "Current above normal or grounded circuit"    
FMI 13     "Out of calibration"    
CID 1521 Rotary Switch (Variable Shift Control)    
FMI 03     "Voltage above normal or shorted high"    
FMI 04     "Voltage below normal or shorted low"    
CID 1716 Detent Electromagnet (Raise/Lower)    
FMI 03     "Voltage above normal or shorted high"    
FMI 06     "Current above normal or grounded circuit"    
CID 1721 Detent Electromagnet (Rackback/Dump)    
FMI 03     "Voltage above normal or shorted high"    
FMI 06     "Current above normal or grounded circuit"    

Information System:

R2900 Load Haul Dump Parking (Remote Control)
140H and 160H Motor Graders Engine Supplement Alternator - Remove and Install
RM-350B Road Reclaimer/Soil Stabilizer Machine Systems Rollover Protective Structure (ROPS) - Remove and Install
D350E Series II and D400E Series II Articulated Trucks Power Train Output Transfer Gear Group
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Braking System Vane Pump (Implement, Pilot, Brake)
2002/09/16 An Updated Air Starting Control Group Improves Durability of the Lines {5500, 5501}
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Aftercooler - Remove and Install - Aftercooler Housing with 12 bolts
14H Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Disassemble
14H Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Assemble
R1600G Load Haul Dump Hydraulic System Sequence Valve (Float) - Test and Adjust
R1600 Load Haul Dump Hydraulic System Relief Valve (Lift Circuit) - Test and Adjust
R2900 Load Haul Dump Operation (Remote Control)
IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader Service Tools
574B Forwarder Power Train Hydrostatic Drive System Performance - Test
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Features
Installation Guide for the Machine Security System on Skid Steer Loaders{7631}
IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader Connector Contact Description
140H and 160H Motor Graders Engine Supplement Air Cleaner - Remove and Install
AP555E and BG555E Asphalt Pavers Machine Systems Hydraulic Cylinder (Truck Hitch)
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Fuel Priming Pump - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Air Inlet Manifold - Remove and Install
574B Forwarder Hydraulic System Steering Cylinder Pressure - Test and Adjust
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Electrical Components