IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader Service Tools Caterpillar


Service Tools
`

The following service tools should be used to aid in troubleshooting the electrical system.

Table 1
Service Tools    
Part Number     Part    
    AVS Electronic Technician    
6V-7070
9U-7330    
Digital Multimeter    
8T-3224     Needle Tip Group    
7X-1710     Multimeter Probe Group    
8T-8726     Adapter Cable Assembly    
9U-7246     Connector Repair Kit
DT    
4C-3406     Connector Repair Kit    



Illustration 1g00774942

Connections for the Communication Adapter II and the Electronic Technician (ET)

The components that are needed in order to use the Communication Adapter II and the AVS Electronic Technician in order to determine diagnostic codes are listed:

(6) Cable

(7) 171-4400 Communication Adapter II

(8) Service diagnostic cable.

(9) Current version of AVSpare Electronic Technician software and an IBM-COMPATIBLE personal computer

Reference: See Special Publication, NEHS0758, "Communications Adapter II User's Manual Contains Software".

Note: AVSpare Electronic Technician (ET) is a software program that can be used on an IBM compatible personal computer.

In order to use the AVSpare Electronic Technician (ET), order the following materials: Special Publication, JERD2124, "ET Single Use Program License", Special Publication, JEHP1026, "Information and Requirements Sheet", 7X-1425 Data Link Cable and the Data Subscription and Special Publication, JERD2142, "Data Subscription". The Special Publication, JEHP1026, "Information and Requirements Sheet" lists the required hardware and the features of the ET.

The Electronic Technician (ET) is not required in order to determine the diagnostic codes and the ET is not required in order to clear the diagnostic codes. However, the process of determining the diagnostic codes is easier and faster by using the ET. The ET can also display information on the history of a diagnostic code and the parameter status of diagnostic codes. These features allow the ET to be a useful tool for troubleshooting.

The Electronic Technician (ET) is used to communicate to the electronic control module over the data link by connecting to the machine diagnostic connector. For more information and the locations of the connectors, see Troubleshooting, "Electrical Components and Connector Locations" and the Electrical System Schematic in your machine's Service Manual.

For instructions on servicing Sure Seal connectors, see Special Instruction, SMHS7531. For instructions on servicing Deutsch connectors, see Special Instruction, SEHS9615.

Use the digital multimeter for measuring resistance or for measuring voltage. For instructions about the use of the 6V-7070 Digital Multimeter, see Special Instruction, SEHS7734. The 7X-1710 Multimeter Probe measures the voltage at the connectors without disconnecting the connectors. The probe cables are pushed into the back of the connector along the wire. The 8T-8726 Adapter Cable has a breakout with 3 pins. The adapter cable is used for measurements in the sensor circuits.

Note: Except for harness tests, using continuity testers such as the 8T-0500 Continuity Tester or voltage testers such as the 5P-7277 Voltage Tester is not recommended for today's AVSpare electrical circuits.

Information System:

IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader Diagnostic Code List
R2900 Load Haul Dump Parking (Remote Control)
140H and 160H Motor Graders Engine Supplement Alternator - Remove and Install
RM-350B Road Reclaimer/Soil Stabilizer Machine Systems Rollover Protective Structure (ROPS) - Remove and Install
D350E Series II and D400E Series II Articulated Trucks Power Train Output Transfer Gear Group
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Braking System Vane Pump (Implement, Pilot, Brake)
2002/09/16 An Updated Air Starting Control Group Improves Durability of the Lines {5500, 5501}
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Aftercooler - Remove and Install - Aftercooler Housing with 12 bolts
14H Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Disassemble
14H Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Assemble
R1600G Load Haul Dump Hydraulic System Sequence Valve (Float) - Test and Adjust
R1600 Load Haul Dump Hydraulic System Relief Valve (Lift Circuit) - Test and Adjust
574B Forwarder Power Train Hydrostatic Drive System Performance - Test
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Features
Installation Guide for the Machine Security System on Skid Steer Loaders{7631}
IT38G Series II Integrated Toolcarrier and 938G Series II Wheel Loader Connector Contact Description
140H and 160H Motor Graders Engine Supplement Air Cleaner - Remove and Install
AP555E and BG555E Asphalt Pavers Machine Systems Hydraulic Cylinder (Truck Hitch)
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Fuel Priming Pump - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Air Inlet Manifold - Remove and Install
574B Forwarder Hydraulic System Steering Cylinder Pressure - Test and Adjust
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Electrical Components
14H Motor Grader 3176C Engine Supplement Air Compressor - Remove