Wheel and Tire (Rear) - Remove and Install
`
16M Motor Grader Power Train
[KENR6019]
16M Motor Grader Power Train
Drive Shaft - Remove and Install
16M Motor Grader Power Train
Drive Chain - Install
POWER TRAIN
WHEEL GP
16M Motor Grader Power Train
Wheel and Tire (Rear) - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 425-0952 | Chock | 2 |
B | 439-3940 | Bracket As | 2 |
C(1) | 9U-7540 | Lift Stand | 2 |
447-0910 | Electric Hydraulic Pump Gp (115V) | 1 | |
447-0911 | Electric Hydraulic Pump Gp (230V) | 1 | |
C1 | OR | ||
504-9790 | Lift Gp (60 Hz)(2) | 2 | |
504-9792 | Lift Gp (50 Hz)(3) | 2 |
Show/hide table
(1) | Use Tooling (C) or (C1) based on requirements. |
(2) | Operating-Voltage (480V - 240V) |
(3) | Operating-Voltage (400V - 200V) |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Connect the steering frame lock. Refer to Operation and Maintenance Manual, "Steering Frame Lock".
Show/hide table
Illustration 1 g01389301 - Use Tooling (A) to chock the front wheels.
Show/hide table
Illustration 2 g03890706 - Attach Tooling (B) and a suitable lifter device to fender assembly (1). The weight of fender assembly (1) is approximately
188 kg (415 lb) .Show/hide tableIllustration 3 g03890712 - Remove bolts (2). Remove bolts (3).
Show/hide table
Illustration 4 g03890723 Show/hide tableIllustration 5 g03890726 - Remove bolts (4).
- Remove bolts (5). Remove fender assembly (1).
Show/hide table
Illustration 6 g03890728 For Tooling (C) - Position Tooling (C) as shown to raise the rear of the machine until the rear wheels are off the ground.
Show/hide table
Illustration 7 g06411090 Typical Example
For Tooling (C1) - Position Tooling (C1) as shown to raise the rear of the machine until the rear wheels are off the ground. Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (C1).
Show/hide table
Illustration 8 g06266190 Typical Example - Attach a suitable lifting device onto rear wheel and tire (6). Remove bolts (7). Remove rear wheel and tire (6) from the spindle hub. The weight of rear wheel and tire (6) is approximately
340 kg (750 lb) . Repeat this step for the remaining wheels.
- Install rear wheel and tire (6) in the reverse order of removal.
- Tighten bolts (7) to a torque of
1800 ± 200 N·m (1328 ± 148 lb ft) .
Information System:
24M Motor Grader Hydraulic and Steering System
Pump Control Valve (Implement, Steering)
587R Pipelayer Power Train
Transmission Hydraulic Control Valve - Remove
770 and 772 Off-Highway Truck/Tractors
Metering Pump (Steering) - Remove and Install
0R-9393 Cylinder Pack Gp Piston Ring Position on Certain C16, 3406E, and 3456 Engines{1215, 1225}
584 and 584HD Forwarders
Slope Operation
24M Motor Grader Hydraulic and Steering System
Piston Pump (Implement and Steering)
16M Motor Grader Machine Systems
Piston Pump (Hydraulic Fan) - Assemble
EquipmentManager User Guide
Getting Started
16M Motor Grader Machine Systems
Piston Pump (Hydraulic Fan) - Disassemble
541 Track Feller Buncher, 551 Track Feller Buncher and 552 Track Feller Buncher Machine Systems
Swing System
AccuGrade</SUP> Laser (CB420)
Determining Detected Faults (Electronic Service Tool)
AccuGrade</SUP> Laser (CB420)
Service Tools
16M Motor Grader Power Train
Drive Chain - Install
AccuGrade</SUP> Laser (CB420)
Full Sensor - Calibrate
16M Motor Grader Power Train
Drive Chain - Remove
AccuGrade</SUP> Laser (CB420)
Module - Flash Program
Problems with Bias Ply Tires on Specific Off-Highway Trucks{4203}
541 Track Feller Buncher, 551 Track Feller Buncher and 552 Track Feller Buncher Machine Systems
Pilot Hydraulic System
R1600G Load Haul Dump
Cooling System Coolant Additive (DEAC) - Add
541 Track Feller Buncher, 551 Track Feller Buncher and 552 Track Feller Buncher Machine Systems
Pump Flow - Test
Cleaning the Compression Brake{1129}
216B2, 226B2, 232B2, 236B2, 242B2 and 252B2 Skid Steer Loaders
Plate Locations and Film Locations
216B2, 226B2, 232B2, 236B2, 242B2 and 252B2 Skid Steer Loaders
Engine Starting
216B2, 226B2, 232B2, 236B2, 242B2 and 252B2 Skid Steer Loaders
Operation Information