16M Motor Grader Power Train Housing (Tandem) - Remove and Install Caterpillar


Housing (Tandem) - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     140-7742     Sleeve     2    

Start By:

  1. Remove the rear wheels. Refer to Disassembly and Assembly, "Wheel and Tire (Rear) - Remove and Install".
  2. Remove the service brakes. Refer to Disassembly and Assembly, "Service Brake (Wheel Spindle) - Remove".


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


Note: Inspect the O-ring seals. Replace the O-ring seals that are worn or damaged.




    Illustration 1g01389705

  1. Disconnect hose assembly (1) . Attach Tooling (A) and two suitable lifting devices onto tandem housing assembly (2) . The weight of tandem housing assembly (2) is approximately 621 kg (1370 lb).



    Illustration 2g01389728

  1. Remove bolts (3) .



    Illustration 3g01389730

  1. Remove tandem housing assembly (2) . The weight of tandem housing assembly (2) is approximately 621 kg (1370 lb).



    Illustration 4g01389733

  1. Remove O-ring seal (4) .

Installation Procedure

Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     140-7742     Sleeve     2    
B     -     Loctite 271     -    


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.





    Illustration 5g01389733

  1. Install O-ring seal (4) .



    Illustration 6g02361117

  1. Ensure that the lubrication port (X) is orientated vertically on both side of the machine.



    Illustration 7g01389730

  1. Use Tooling (A) and two suitable lifting devices in order to install tandem housing assembly (2) . The weight of tandem housing assembly (2) is approximately 621 kg (1370 lb).



    Illustration 8g01389728

    Note: Do not use the four bolts that are on the corners of the final drive to pull the tandem housing against the final drive.

  1. Apply Tooling (B) to bolts (3) . Install bolts (3) . Tighten bolts (3) to a torque of 530 ± 70 N·m (391 ± 52 lb ft).



    Illustration 9g01389739

  1. Connect hose assembly (1) .

End By:

  1. Install the service brakes. Refer to Disassembly and Assembly, "Service Brake (Wheel Spindle) - Install".
  2. Install the rear wheels. Refer to Disassembly and Assembly, "Wheel and Tire (Rear) - Remove and Install".

Information System:

AP655D and BG655D Asphalt Pavers Machine Systems Steering Column - Assemble
AP655D and BG655D Asphalt Pavers Machine Systems Steering Column - Disassemble
16M Motor Grader Power Train Service Brake (Wheel Spindle) - Install
16M Motor Grader Power Train Service Brake (Wheel Spindle) - Remove
AP655D Asphalt Paver Machine Systems Hydraulic Tank - Remove and Install
C4.4 and C6.6 Engines for Caterpillar Built Machines Glossary
C4.4 and C6.6 Engines for Caterpillar Built Machines System Overview
587R Pipelayer Power Train Priority Valve - Assemble
587R Pipelayer Power Train Priority Valve - Disassemble
EquipmentManager Dealer Administrator Manual Product Link Installation
587R Pipelayer Power Train Priority Valve - Install
24M Motor Grader Power Train Electronic Control System MID 027 - CID 2734 - FMI 04
C4.4 and C6.6 Engines for Caterpillar Built Machines Sensors and Electrical Connectors
16M Motor Grader Power Train Rear Axle, Differential and Final Drive - Remove
16M Motor Grader Power Train Rear Axle, Differential and Final Drive - Install
C4.4 and C6.6 Engines for Caterpillar Built Machines Engine Wiring Information
AS3251C Asphalt Screed Electronic Control Module (Screed)
Procedure to Install Forward/Neutral/Reverse (FNR) Switch{5702, 7332}
AS3251C Asphalt Screed Operator Controls
2007/06/25 Correction to Operation and Maintenance Manual , "Hoist System and Brake System Oil Level - Check" {5056}
16M Motor Grader Power Train Transmission Oil Filter Base - Remove
16M Motor Grader Power Train Transmission Oil Filter Base - Install
AS3251C Asphalt Screed Screed Components
24M Motor Grader Power Train Electronic Control System MID 027 - CID 1639 - FMI 09