EPC Parts Catalogs

16M Motor Grader Power Train Transmission Oil Cooler - Install Caterpillar


  1. Home
  2. Disassembly and Assembly
  3. #128466
Transmission Oil Cooler - Install
`
16M Motor Grader Power Train [KENR6019]
16M Motor Grader Power Train Transmission Oil Cooler - Remove
16M Motor Grader Power Train Transmission - Disassemble
POWER TRAIN
COOLER GP
16M Motor Grader Power Train Transmission Oil Cooler - Remove
16M Motor Grader Power Train Transmission Oil Cooler - Install
1.1. Installation Procedure

Installation Procedure

Show/hide table
Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
A  138-7575  Link Bracket  1 

Show/hide table
NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

    Show/hide table
    Illustration 1g01390204

  1. Install O-ring seals (17).
    Show/hide table
    Illustration 2g01390202

  2. Install O-ring seal (16). Install coupling (15).
    Show/hide table
    Illustration 3g01390197
    Show/hide table
    Illustration 4g01390200

  3. Use Tooling (A) and a suitable lifting device in order to install transmission oil cooler (12). The weight of transmission oil cooler (12) is approximately 30 kg (66 lb). Install bolts (14) and bolts (13).
    Show/hide table
    Illustration 5g01390188

  4. Install bracket (11).
    Show/hide table
    Illustration 6g01390185

  5. Install bracket (10).
    Show/hide table
    Illustration 7g01390120

  6. Install elbow (9).
    Show/hide table
    Illustration 8g01390112

  7. Connect hose assemblies (8). Connect tube assembly (7). Connect hose assembly (6).
    Show/hide table
    Illustration 9g01390107

  8. Install tube (5). Connect elbow (4).
    Show/hide table
    Illustration 10g01390106

  9. Install clamps (3).
    Show/hide table
    Illustration 11g01390103

  10. Connect hose (2).
    Show/hide table
    Illustration 12g01390102

  11. Install panels (1).

  12. Fill the engine coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".

  13. Fill the hydraulic oil. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change".

Information System:

16M Motor Grader Power Train Transmission Oil Cooler - Remove
24M Motor Grader Power Train Electronic Control System MID 027 - CID 1639 - FMI 09
AS3251C Asphalt Screed Screed Components
16M Motor Grader Power Train Transmission Oil Filter Base - Install
16M Motor Grader Power Train Transmission Oil Filter Base - Remove
2007/06/25 Correction to Operation and Maintenance Manual , "Hoist System and Brake System Oil Level - Check" {5056}
AS3251C Asphalt Screed Operator Controls
Procedure to Install Forward/Neutral/Reverse (FNR) Switch{5702, 7332}
AS3251C Asphalt Screed Electronic Control Module (Screed)
C4.4 and C6.6 Engines for Caterpillar Built Machines Engine Wiring Information
16M Motor Grader Power Train Rear Axle, Differential and Final Drive - Install
16M Motor Grader Power Train Rear Axle, Differential and Final Drive - Remove
C15 and C18 Generator Set Engines Fan Guard - Remove and Install
587R Pipelayer Power Train Transmission and Bevel Gears - Remove
587R Pipelayer Power Train Transmission and Bevel Gears - Install
AS4251C Asphalt Paver Specifications
C15 and C18 Generator Set Engines Fan - Remove and Install
AS3251C Asphalt Screed Screed Control System
AP655D and BG655D Asphalt Pavers Propel System Piston Pump Flow - Test - Steel Track
EquipmentManager Dealer Administrator Manual Setup Subscriptions
773F and 775F Off-Highway Truck Radio Mount
AccuGrade</SUP> Laser (CB420) AS 1 Memory Fault
Replacement of the Cover Assembly on the Cab Door{7308}
Bench Test Procedure for Hydraulic Piston Pumps{5070}