Final Drive Planetary (Drum Propel) - Assemble
`
CB14 Paving Compactor Machine Systems
[KENR6008]
CB14 Paving Compactor Machine Systems
Final Drive Planetary (Drum Propel) - Disassemble
CB14 Paving Compactor Machine Systems
Final Drive Planetary (Drum Propel) - Install
POWER TRAIN
GEARBOX GP
CB14 Paving Compactor Machine Systems
Final Drive Planetary (Drum Propel) - Remove
CB14 Paving Compactor Machine Systems
Final Drive Planetary (Drum Propel) - Disassemble
CB14 Paving Compactor Machine Systems
Final Drive Planetary (Drum Propel) - Assemble
CB14 Paving Compactor Machine Systems
Final Drive Planetary (Drum Propel) - Install
1.1. Assembly Procedure
Assembly Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tools     | Part Number     | Part Description     | Qty     |
C     | 1P-1853     | Retaining Ring Pliers     | 1     |
D     | 1P-1859     | Retaining Ring Pliers     | 1     |
F     | 5P-5197     | Retaining Ring Pliers As     | 1     |
H     | 1P-0510     | Driver Gp     | 1     |
K     | 1P-1861     | Retaining Ring Pliers     | 1     |
L     | 1P-0520     | Driver Gp     | 1     |
M     | 314-9076     | Seal Installer     | 1     |
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
- Place bearing (24) into gearbox housing (15) .
Show/hide table
![]() | |
Illustration 1 | g01391378 |
- Use Tooling (L) and a suitable press in order to install bearing (24) to gearbox housing (15) .
Show/hide table
![]() | |
Illustration 2 | g01391380 |
- Install spacer (23) to gearbox housing (15) .
Show/hide table
![]() | |
Illustration 3 | g01391381 |
- Use Tooling (K) in order to install retaining ring (22) to gearbox housing (15) .
Show/hide table
![]() | |
Illustration 4 | g01391422 |
- Install O-ring seal (21) to gearbox housing (15) .
Show/hide table
![]() | |
Illustration 5 | g01391424 |
- Install bearing (19) to gearbox housing (15) .
Show/hide table
![]() | |
Illustration 6 | g01391384 |
- Use Tooling (L) and a suitable press in order to install bearing (19) to gearbox housing (15) .
Show/hide table
![]() | |
Illustration 7 | g01391385 |
- Use Tooling (M) to install half seal (20) to flanged hub (2) .
Note: Clean half seal (20) and apply a thin coat of oil to half seal.
Show/hide table
![]() | |
Illustration 8 | g01391388 |
- Use a suitable press in order to install flanged hub (2) to gearbox housing (15) .
Show/hide table
![]() | |
Illustration 9 | g01391393 |
- Use Tooling (F) to install retaining ring (18) to flanged hub (2) .
Show/hide table
![]() | |
Illustration 10 | g01391442 |
- Use Tooling (H) and a suitable press to Install gears (17) on flanged hub (2) .
Show/hide table
![]() | |
Illustration 11 | g01391398 |
- Use Tooling (D) in order to install retaining ring (16) to gears (17) .
Show/hide table
![]() | |
Illustration 12 | g01391465 |
- Install O-ring seal (14) to gearbox housing (15) .
Show/hide table
![]() | |
Illustration 13 | g01391469 |
- Install end cover (13) to gearbox housing (15). Install plug (12) to end cover (13) .
Show/hide table
![]() | |
Illustration 14 | g01391404 |
- Install retaining ring (11) to gearbox housing (15) .
Show/hide table
![]() | |
Illustration 15 | g01391405 |
- Install gear (10) .
Show/hide table
![]() | |
Illustration 16 | g01391478 |
- Use Tooling (C) in order to install retaining ring (8) to brake shaft (7) .
Show/hide table
![]() | |
Illustration 17 | g01391479 |
- Install brake shaft (7) .
Show/hide table
![]() | |
Illustration 18 | g01391481 |
- Install disc (9). Install discs (9). Repeat the operation until all seven bronze disks and eight steel disks have been assembled.
Show/hide table
![]() | |
Illustration 19 | g01391575 |
Show/hide table
![]() | |
Illustration 20 | g01391576 |
- Install backup ring (6) and O-ring seal (5) in flanged hub (2) .
Show/hide table
![]() | |
Illustration 21 | g01391581 |
- Install brake piston (4) .
Show/hide table
![]() | |
Illustration 22 | g01391588 |
- Use Tooling (H) and a suitable press to install brake piston (4) into flanged hub (2) .
Show/hide table
![]() | |
Illustration 23 | g01391589 |
- Install springs (3) into flanged hub (2) according to the previously marked positions.
Show/hide table
![]() | |
Illustration 24 | g01391592 |
- Install O-ring seal (1) into the brake port of flanged hub (2) .
Show/hide table
![]() | |
Illustration 25 | g01390786 |
- Verify that the axial distance is 59.70 ± .40 mm (2.35 ± 0.02 inch) before you mount the final drive planetary.
End By: Install the final drive planetary (drum propel). Refer to Disassembly and Assembly, "Final Drive Planetary (Drum Propel) - Install".
Information System:
CB14 Paving Compactor Machine Systems
Final Drive Planetary (Drum Propel) - Disassemble
CB14 Paving Compactor Machine Systems
Final Drive Planetary (Drum Propel) - Remove
Fluid Power and Electrical Graphic Symbols
Electrical Power Graphic Symbols
Inspection of Rim Assemblies of Off-Highway Trucks {4201, 4209}
CB14 Paving Compactor Machine Systems
Drum - Install
AS4251C Asphalt Paver
Operator Controls
AS4251C Asphalt Paver
Operator Controls - Main Control Panel
AS4251C Asphalt Paver
Operator Controls - Right Control Panel
AS4251C Asphalt Paver
Operator Controls - Left Control Panel
AP655D and BG655D Asphalt Pavers Propel System
Piston Pump Neutral - Test and Adjust - Right Propel Pump (Steel Track)
CB14 Paving Compactor Machine Systems
Drum - Remove
3176C, 3406E and 3456 Industrial Engines
Electronic Service Tools
CB14 Paving Compactor Machine Systems
Final Drive Planetary (Drum Propel) - Install
EquipmentManager Dealer Administrator Manual
Manage Equipment Groups
R2900G Load Haul Dump
Lifting and Tying Down the Machine
C4.4 (Mech) Industrial Engine
Engine Valve Lash - Inspect/Adjust
AP655D and BG655D Asphalt Pavers Propel System
Piston Pump Neutral - Test and Adjust - Left Propel Pump (Steel Track)
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train
Track (Rubber) - Remove and Install
AP655D and BG655D Asphalt Pavers Propel System
Relief Valve (Charge) - Test and Adjust - Right Pump (Steel Track)
AP655D and BG655D Asphalt Pavers Propel System
Pump Synchronization - Test and Adjust - Steel Track
C15 and C18 Generator Set Engines
Fuel Cooler - Remove and Install
24M Motor Grader Power Train Electronic Control System
MID 027 - CID 0679 - FMI 03
C15 and C18 Generator Set Engines
Expansion Tank - Remove and Install
24M Motor Grader Power Train Electronic Control System
MID 027 - CID 0679 - FMI 05