Expansion Tank - Remove and Install
`
C15 and C18 Generator Set Engines
[RENR8643]
C15 and C18 Generator Set Engines
Fuel Cooler - Remove and Install
C15 and C18 Generator Set Engines
Radiator Bottom Tank - Remove and Install - Jacket Water Heater
COOLING SYSTEM
TANK GP-EXPANSION
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Show/hide table
Illustration 1 g01390905 - Disconnect hose (1).
Show/hide table
Illustration 2 g01390907 - Disconnect hoses (3), (4), and (6).
- Disconnect harness assembly (5).
- Remove bolts (2) and expansion tank (7).
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Place expansion tank (7) in position and install bolts (2).
- Connect harness assembly (5).
- Connect hoses (6), (4), and (3).
Show/hide table
Illustration 4 g01390905 - Connect hose (1).
- Fill the expansion tank to the correct level. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Show/hide table
![]() | |
Illustration 3 | g01390907 |
Information System:
24M Motor Grader Power Train Electronic Control System
MID 027 - CID 0679 - FMI 03
C15 and C18 Generator Set Engines
Fuel Cooler - Remove and Install
AP655D and BG655D Asphalt Pavers Propel System
Pump Synchronization - Test and Adjust - Steel Track
AP655D and BG655D Asphalt Pavers Propel System
Relief Valve (Charge) - Test and Adjust - Right Pump (Steel Track)
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train
Track (Rubber) - Remove and Install
AP655D and BG655D Asphalt Pavers Propel System
Piston Pump Neutral - Test and Adjust - Left Propel Pump (Steel Track)
C4.4 (Mech) Industrial Engine
Engine Valve Lash - Inspect/Adjust
R2900G Load Haul Dump
Lifting and Tying Down the Machine
EquipmentManager Dealer Administrator Manual
Manage Equipment Groups
CB14 Paving Compactor Machine Systems
Final Drive Planetary (Drum Propel) - Install
CB14 Paving Compactor Machine Systems
Final Drive Planetary (Drum Propel) - Assemble
CB14 Paving Compactor Machine Systems
Final Drive Planetary (Drum Propel) - Disassemble
24M Motor Grader Power Train Electronic Control System
MID 027 - CID 0679 - FMI 05
587R Pipelayer Machine Systems
Fuel Tank - Remove and Install
AP655D and BG655D Asphalt Pavers Propel System
Relief Valve (Charge) - Test and Adjust - Left Pump (Steel Track)
541 Track Feller Buncher, 551 Track Feller Buncher and 552 Track Feller Buncher Machine Systems
Reversing Fan - Test
R2900G Load Haul Dump
Safety Messages
R2900G Load Haul Dump
Additional Messages
R2900G Load Haul Dump
Engine Starting with Auxiliary Start Receptacle
R1700G Load Haul Dump
Lifting and Tying Down the Machine
C4.4 and C6.6 Engines for Caterpillar Built Machines
Indicator Lamps
AP655D and BG655D Asphalt Pavers Propel System
Speed Sensor (Propel Motor) - Adjust - Steel Track Machine
3412E Engine for Caterpillar Built Machines
Event Code List
AP655D and BG655D Asphalt Pavers Propel System
Pressure Limiter Valve - Test and Adjust - Right Propel Pump (Steel Track)