Fuel Transfer Pump - Install
`
C6.6 Engines for Caterpillar Built Machines
[KENR6081]
C6.6 Engines for Caterpillar Built Machines
Fuel Transfer Pump - Remove
C6.6 Engines for Caterpillar Built Machines
Fuel Manifold (Rail) - Remove and Install
FUEL SYSTEM
PUMP GP-FUEL TRANSFER
C6.6 Engines for Caterpillar Built Machines
Fuel Transfer Pump - Remove
C6.6 Engines for Caterpillar Built Machines
Fuel Transfer Pump - Install
1.1. Installation Procedure
Installation Procedure
Show/hide table
NOTICE |
---|
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training. Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system. |
- Ensure that the mating surfaces of fuel injection pump (1) and fuel transfer pump (2) are clean and free from damage.
- Install a new O-ring seal (11) to fuel transfer pump (2) . Lubricate the O-ring seal with clean engine oil.
Show/hide table
![]() | |
Illustration 1 | g01335045 |
- Align the holes in fuel transfer pump (2) with dowels (10) in fuel injection pump (1) . Install the fuel transfer pump to the fuel injection pump.
Show/hide table
![]() | |
Illustration 2 | g01335043 |
- Use an allen wrench with a ball end to install the allen head screws (3) . Tighten the allen head screws to a torque of 30 N·m (22 lb ft).
Show/hide table
![]() | |
Illustration 3 | g01334899 |
- Remove the plugs and the caps from the ports and tube assemblies.
- Install tube assembly (4) for the engine oil supply to fuel injection pump (1) . Install new washers to the banjo bolt for oil supply tube assembly. Install the banjo bolt to the cylinder block. Tighten both connectors to a torque of 15 N·m (11 lb ft).
- Install tube assembly (8) for the fuel return to fuel transfer pump (2) and to the cylinder head. Tighten both banjo bolts to a torque of 21 N·m (15 lb ft).
- Install a new O-ring seal to connector (6) . Install connector (6) to fuel transfer pump (2) . Tighten the connector to torque of 15 N·m (11 lb ft).
- If necessary, install a new O-ring seal to connector (9) and install connector (9) to fuel transfer pump (2) . Tighten the connector to torque of 15 N·m (11 lb ft).
- Connect plastic tube assembly (5) to the outlet of fuel transfer pump (2) .
- Install plastic tube assembly (7) to fuel transfer pump (2) .
- Turn the fuel supply to the ON position.
- Remove the air from the fuel system. Refer to System Operation, Testing and Adjusting, "Fuel System - Prime".
Information System:
C6.6 Engines for Caterpillar Built Machines
Fuel Transfer Pump - Remove
C6.6 Engines for Caterpillar Built Machines
Fuel Filter Base - Remove and Install - Secondary Fuel Filter
24M Motor Grader Power Train
Transmission
24M Motor Grader Power Train Electronic Control System
MID 027 - CID 0679 - FMI 06
3412E Engine for Caterpillar Built Machines
Oil Pressure Is Low
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train
Track Drive - Remove
C15 and C18 Generator Set Engines
Radiator Core - Remove and Install - Jacket Water Heater
770 and 772 Off-Highway Truck/Tractors
Steering Link - Remove and Install
Installation of Fuel Lines{1274}
C4.4 and C6.6 Engines for Caterpillar Built Machines
Intake Air Temperature Is Too High
C4.4 and C6.6 Engines for Caterpillar Built Machines
Excessive Fuel Consumption
C4.4 and C6.6 Engines for Caterpillar Built Machines
Engine Misfires, Runs Rough or Is Unstable
C6.6 Engines for Caterpillar Built Machines
Fuel Manifold (Rail) - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Fuel Injection Lines - Remove
C6.6 Engines for Caterpillar Built Machines
Fuel Injection Lines - Install
C6.6 Engines for Caterpillar Built Machines
Fuel Injection Pump - Remove
C6.6 Engines for Caterpillar Built Machines
Fuel Injection Pump - Install
C6.6 Engines for Caterpillar Built Machines
Fuel Injection Pump Gear - Remove
C6.6 Engines for Caterpillar Built Machines
Fuel Injection Pump Gear - Install
C6.6 Engines for Caterpillar Built Machines
Turbocharger - Remove - Side Mounted Turbocharger
C6.6 Engines for Caterpillar Built Machines
Turbocharger - Remove - Turbocharger Top Mounted
C6.6 Engines for Caterpillar Built Machines
Turbocharger - Install - Side Mounted Turbocharger
C6.6 Engines for Caterpillar Built Machines
Turbocharger - Install - Turbocharger Top Mounted
C6.6 Engines for Caterpillar Built Machines
Wastegate Solenoid - Remove and Install