C6.6 Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install Caterpillar


Fuel Manifold (Rail) - Remove and Install
`
1.1. Removal Procedure
2.2. Engines with Bracket Installed
3.2. Engines without Bracket Installed
4.1. Installation Procedure
5.2. Engines with Bracket Installed
6.2. Engines without Bracket Installed

Removal Procedure

Start By:

  1. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove".

  2. If necessary, remove the fuel pressure sensor. Refer to Disassembly and Assembly, "Fuel Pressure Sensor - Remove and Install".

------ WARNING! ------

Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.



NOTICE

Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.

Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.

Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.


Engines with Bracket Installed

  1. If the engine is equipped with a cover over the fuel system this will need to be removed.


    Illustration 1g01335251
    The fuel manifold is shown with fuel injection lines in position.

  2. If necessary, remove fuel pressure sensor (5). Refer to Disassembly and Assembly, "Fuel Pressure Sensor - Remove and Install".

  3. If fuel pressure sensor (5) does not require removal, slide locking tab (4) into the unlocked position. Disconnect the plug on harness assembly (9) from fuel pressure sensor (5).

  4. Disconnect tube assembly (7) from the fuel pressure relief valve on fuel manifold (3). Immediately cap the open port in fuel manifold (3) with a new cap. Immediately plug the open end of tube assembly (7) with a new plug.

  5. Remove bolts (2) and spacer from fuel manifold (3).

    Note the position of the spacer for installation purposes.

  6. Remove the bolt from fuel injection line clamp (6). Remove clamp assembly from the bracket.

  7. Remove bracket (1) from fuel manifold (3).

  8. Remove fuel manifold (3) from mounting bracket (8).

Engines without Bracket Installed

  1. If the engine is equipped with a cover over the fuel system this will need to be removed.


    Illustration 2g03326199
    Typical example

  2. If necessary, remove fuel pressure sensor (5). Refer to Disassembly and Assembly, "Fuel Pressure Sensor - Remove and Install".

  3. If fuel pressure sensor (5) does not require removal, slide locking tab (4) into the unlocked position. Disconnect the plug on harness assembly (8) from fuel pressure sensor (5).

  4. Disconnect tube assembly (6) from the fuel pressure relief valve on fuel manifold (3). Immediately cap the open port in fuel manifold (3) with a new cap. Immediately plug the open end of tube assembly (6) with a new plug.

  5. Remove bolts (1) and spacer (2) from fuel manifold (3).

    Note the position of the spacer for installation purposes.

  6. Remove fuel manifold (3) from mounting bracket (7).

Installation Procedure


NOTICE

Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.

Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.

Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.


Engines with Bracket Installed

  1. Ensure that all ports on the fuel manifold are capped. Ensure that the fuel manifold is externally clean and free from damage.

    Note: Do not install a fuel manifold that has not been capped. All caps must be left in place until the fuel injection lines or the fuel pressure sensor are installed.



    Illustration 3g01335251
    The fuel manifold is shown with fuel injection lines in position.

  2. Position fuel manifold (3) on mounting bracket (8).

  3. Install bracket (1) from fuel manifold (3).

  4. Install bolts (2) to fuel manifold (3) finger tight.

  5. Install the bolt to fuel injection line clamp (6). Tighten bolts (6) to a torque of 22 N·m (16 lb ft). Ensure that fuel injection line does not contact any other engine component.

  6. Install a new set of fuel injection lines and seals. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install" for more information.

  7. Remove the plug from tube assembly (7). Remove the cap from the appropriate port in fuel manifold (3). Connect tube assembly (7) to the fuel pressure relief valve on fuel manifold (3). Tighten the connection to a torque of 30 N·m (22 lb ft).

  8. If fuel pressure sensor (5) was not removed from fuel manifold (3), connect the plug on harness assembly (9) to fuel pressure sensor (5). slide locking tab (4) into the locked position.

    If fuel pressure sensor (5) was removed from fuel manifold (3), install fuel pressure sensor (5) and a new sealing washer. Refer to Disassembly and Assembly, "Fuel Pressure Sensor - Remove and Install" for more information.

  9. Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for more information.

  10. If the engine was equipped with a cover over the fuel system this will need to be installed.

Engines without Bracket Installed

  1. Ensure that all ports on the fuel manifold are capped. Ensure that the fuel manifold is externally clean and free from damage.

    Note: Do not install a fuel manifold that has not been capped. All caps must be left in place until the fuel injection lines or the fuel pressure sensor are installed.



    Illustration 4g03326199
    Typical example

  2. Position fuel manifold (3) on mounting bracket (7).

  3. Install spacer (2) to bolt. Install bolts (1) to fuel manifold (3) finger tight.

  4. Install a new set of fuel injection lines and seals. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install" for more information.

  5. Remove the plug from tube assembly (6). Remove the cap from the appropriate port in fuel manifold (3). Connect tube assembly (6) to the fuel pressure relief valve on fuel manifold (3). Tighten the connection to a torque of 30 N·m (22 lb ft).

  6. If fuel pressure sensor (5) was not removed from fuel manifold (3), connect the plug on harness assembly (8) to fuel pressure sensor (5). slide locking tab (4) into the locked position.

    If fuel pressure sensor (5) was removed from fuel manifold (3), install fuel pressure sensor (5) and a new sealing washer. Refer to Disassembly and Assembly, "Fuel Pressure Sensor - Remove and Install" for more information.

  7. Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for more information.

  8. If the engine was equipped with a cover over the fuel system this will need to be installed.

Information System:

C6.6 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C6.6 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
C6.6 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install - Secondary Fuel Filter
24M Motor Grader Power Train Transmission
24M Motor Grader Power Train Electronic Control System MID 027 - CID 0679 - FMI 06
3412E Engine for Caterpillar Built Machines Oil Pressure Is Low
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Track Drive - Remove
C15 and C18 Generator Set Engines Radiator Core - Remove and Install - Jacket Water Heater
770 and 772 Off-Highway Truck/Tractors Steering Link - Remove and Install
Installation of Fuel Lines{1274}
C4.4 and C6.6 Engines for Caterpillar Built Machines Intake Air Temperature Is Too High
C4.4 and C6.6 Engines for Caterpillar Built Machines Excessive Fuel Consumption
C6.6 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove
C6.6 Engines for Caterpillar Built Machines Fuel Injection Lines - Install
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Remove
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Install
C6.6 Engines for Caterpillar Built Machines Turbocharger - Remove - Side Mounted Turbocharger
C6.6 Engines for Caterpillar Built Machines Turbocharger - Remove - Turbocharger Top Mounted
C6.6 Engines for Caterpillar Built Machines Turbocharger - Install - Side Mounted Turbocharger
C6.6 Engines for Caterpillar Built Machines Turbocharger - Install - Turbocharger Top Mounted
C6.6 Engines for Caterpillar Built Machines Wastegate Solenoid - Remove and Install
C6.6 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Side Mounted Exhaust Manifold