C6.6 Engines for Caterpillar Built Machines Wastegate Solenoid - Remove and Install Caterpillar


Wastegate Solenoid - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure



    Illustration 1g01335778
    Typical example

  1. Follow Steps 1.a through 1.c in order to disconnect wire lead (1).

    1. Disconnect wire lead (1) from the harness assembly.

    2. If harness assembly (1) is secured with a cable strap, remove the cable strap.

    3. Remove wire lead (1) from tube assembly (2).

      Note: The wire lead is secured to the tube assembly with clips.

  2. Disconnect tube assembly (2) from wastegate solenoid (3).

  3. Disconnect tube assembly (4) from wastegate solenoid (3). If tube assembly (4) is secured with tube clips, loosen the bolts for the tube clips.

    Note: The tube clips must be loose in order to release the tube assembly from the wastegate solenoid.

  4. Remove bolts (5) and remove wastegate solenoid (3) from the cylinder block.

  5. Plug or cap all open ports and tube assemblies with new plugs or caps.

Installation Procedure

  1. Remove the plugs or caps from all ports and tube assemblies.


    Illustration 2g01335778
    Typical example

  2. Loosely install wastegate solenoid (3) to tube assembly (2).

  3. Loosely install tube assembly (4) to wastegate solenoid (3).

  4. Install bolts (5) to wastegate solenoid (3). Tighten bolts (5) to a torque of 44 N·m (32.5 lb ft).

  5. Tighten tube assemblies (2) and (4) to a torque of 22 N·m (16 lb ft).

  6. If tube assembly (4) is secured with tube clips, tighten the bolts for the tube clips.

    Tighten M8 bolts to a torque of 22 N·m (16 lb ft). Tighten M10 bolts to a torque of 44 N·m (32.5 lb ft).

  7. Follow Steps 7 through 7.c in order to connect wire lead (1).

    1. Install wire lead (1) to tube assembly (2).

    2. Connect wire lead (1) to the harness assembly for the engine.

    3. If wire lead (1) is secured with a cable strap, install a new cable strap.

Information System:

C6.6 Engines for Caterpillar Built Machines Turbocharger - Install - Turbocharger Top Mounted
C6.6 Engines for Caterpillar Built Machines Turbocharger - Install - Side Mounted Turbocharger
C6.6 Engines for Caterpillar Built Machines Turbocharger - Remove - Turbocharger Top Mounted
C6.6 Engines for Caterpillar Built Machines Turbocharger - Remove - Side Mounted Turbocharger
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Install
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Remove
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove
C6.6 Engines for Caterpillar Built Machines Fuel Injection Lines - Install
C6.6 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove
C6.6 Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install
C6.6 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C6.6 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Side Mounted Exhaust Manifold
C6.6 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Top Mounted Exhaust Manifold
C6.6 Engines for Caterpillar Built Machines Exhaust Elbow - Remove and Install
C6.6 Engines for Caterpillar Built Machines Inlet Manifold - Remove and Install
C6.6 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C6.6 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C6.6 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
EquipmentManager Dealer Administrator Manual Major Repair
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base