Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
`
C6.6 Engines for Caterpillar Built Machines
[KENR6081]
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
COOLING SYSTEM
COOLER GP
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
1.1. Assembly Procedure
2.1. Installation Procedure (Engine Oil Cooler with a Low Mounted Filter Base)
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
![]() | |
Illustration 1 | g01336430 |
Typical example |
- Ensure that cooler matrix (19) is clean and free from damage. Ensure that spacer plate (17) is clean and free from damage. Replace any damaged components.
- Position a new joint (18) onto spacer plate (17). Install cooler matrix (19) to the spacer plate.
- Install bolts (15) finger tight.
Show/hide table
Illustration 2 g01336427 Typical example - Position brackets (5), (10) and (14) onto the assembly of oil cooler (6). Install bolts (7).
Note: Ensure that brackets for the tube assemblies are installed in the correct location and the correct orientation. The bolts are different lengths. Ensure that the different bolts are installed in the correct location.
- Install new joint (16) to the assembly of oil cooler (6). Push bolts (7) through the holes in the joint.
Note: The holes in the joint have serrations that hold the bolts captive.
Installation Procedure (Engine Oil Cooler with a Low Mounted Filter Base)
- Clean the mating surfaces of the cylinder block.
Show/hide table
Illustration 3 g01417038 Typical example of an engine oil cooler with a blanking plate - Install the assembly of oil cooler (6) to the cylinder block. Tighten bolts (7) finger tight.
Show/hide table
Illustration 4 g01336468 Tightening sequence for an engine oil cooler with a blanking plate or with a low mounted oil filter base - Tighten bolts (7) to a torque of
22 N·m (16 lb ft) in the sequence that is shown in Illustration 4. - If the engine has a low mounted oil filter on the left hand side, install the oil filter base. Refer to Disassembly and Assembly, "Oil Filter Base - Remove and Install".
If the engine has a right hand side oil filter, follow Steps 4.a through 4.d in order to install blanking plate (12).
- Install bolts (11) to blanking plate (12).
- Position a new joint onto blanking plate (12).
- Install the assembly of the blanking plate to the assembly of oil cooler (6).
- Tighten bolts (11) to a torque of
22 N·m (16 lb ft) .
- Remove the plugs from tube assembly (9). Remove the caps for the fuel return from the cylinder head and from transfer pump (8). Install tube assembly (9) to the cylinder head and to transfer pump (8).
- Follow Steps 6.a through 6.e in order to connect engine wiring harness (4).
- Place the harness in position.
- Connect engine wiring harness (4) to position sensor (2) for the fuel injection pump.
- Connect engine wiring harness (4) to oil pressure sensor (13).
- Connect engine wiring harness (4) to solenoid (1) for the fuel injection pump.
- Install new cable straps in order to secure engine wiring harness (4) to the assembly of oil cooler (6).
- Remove the plugs from all plastic tube assemblies (3). Remove the caps from the appropriate ports. Install plastic tube assemblies (3).
- Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
- Check the level of the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil Level - Check" for the correct procedure.
End By:
- Install the bracket for the Electronic Control Module. Refer to Disassembly and Assembly, "ECM Bracket - Remove and Install".
Information System:
EquipmentManager Dealer Administrator Manual
Major Repair
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines
Engine Oil Filter Base - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Inlet and Exhaust Valves - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Inlet and Exhaust Valve Springs - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Inlet Manifold - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Exhaust Elbow - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Exhaust Manifold - Remove and Install - Top Mounted Exhaust Manifold
C6.6 Engines for Caterpillar Built Machines
Exhaust Manifold - Remove and Install - Side Mounted Exhaust Manifold
C6.6 Engines for Caterpillar Built Machines
Wastegate Solenoid - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Turbocharger - Install - Turbocharger Top Mounted
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines
Engine Oil Relief Valve - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pump - Remove
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pump - Install
C6.6 Engines for Caterpillar Built Machines
Water Pump - Remove
C6.6 Engines for Caterpillar Built Machines
Water Pump - Install
C6.6 Engines for Caterpillar Built Machines
Water Temperature Regulator - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Flywheel - Remove
24M Motor Grader Power Train Electronic Control System
MID 027 - CID 0379 - FMI 03
C6.6 Engines for Caterpillar Built Machines
Flywheel - Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft Rear Seal - Remove
C6.6 Engines for Caterpillar Built Machines
Crankshaft Rear Seal - Install