Engine Oil Pump - Install
`
C6.6 Engines for Caterpillar Built Machines
[KENR6081]
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pump - Remove
C6.6 Engines for Caterpillar Built Machines
Water Pump - Remove
LUBRICATION SYSTEM
PUMP GP-ENGINE OIL
C6.6 Engines for Caterpillar Built Machines
Engine Oil Relief Valve - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pump - Remove
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pump - Install
1.1. Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
If any part of the engine oil pump is worn or damaged, the complete assembly of the engine oil pump must be replaced. |
- Ensure that all components of the engine oil pump are clean and free from wear or damage. Refer to System Operation, Testing and Adjusting, "Engine Oil Pump - Inspect" for more information. Replace the complete assembly of the engine oil pump if any of the components are worn or damaged.
Show/hide table
Illustration 1 g01398113 Typical example - If necessary, install the pressure relief valve (3). Refer to Disassembly and Assembly, "Engine Oil Relief Valve - Remove and Install" for correct procedure.
Show/hide table
Illustration 2 g01336651 - If necessary, lubricate the internal components for the assembly of the engine oil pump with clean engine oil. Install outer rotor (8) and front cover (7) to the housing of engine oil pump (4). Install the allen head bolts (9). Tighten the allen head bolts to a torque of
22 N·m (16 lb ft) . - Ensure that the dowel (10) and dowel (11) are correctly located in the housing of engine oil pump (4). Position the assembly of the engine oil pump onto the cylinder block.
Note: Ensure that the dowels in the housing of the engine oil pump are aligned with the holes in the cylinder block.
- Install bolts (5). Tighten the bolts to a torque of
22 N·m (16 lb ft) . - Check the backlash between idler gear (12) and the crankshaft gear. Refer to Specifications, "Gear Group (Front)" for further information.
- Install suction pipe (1) and a new gasket (6) to the assembly of the engine oil pump.
- Install bolts (2). Tighten the bolts to a torque to
22 N·m (16 lb ft) . - If suction pipe (6), has a support bracket follow dowel 9.a through dowel 9.c.
- Install the components of the support bracket. Ensure the correct location and orientation of the bracket and the retaining clip.
- Tighten the bolts finger tight in order to align the components of the support bracket.
- Tighten bolts (2) to a torque of
22 N·m (16 lb ft) .
End By:
- Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install" for the correct procedure.
Information System:
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pump - Remove
C6.6 Engines for Caterpillar Built Machines
Engine Oil Relief Valve - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
EquipmentManager Dealer Administrator Manual
Major Repair
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines
Engine Oil Filter Base - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Inlet and Exhaust Valves - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Inlet and Exhaust Valve Springs - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Inlet Manifold - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Exhaust Elbow - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Water Pump - Remove
C6.6 Engines for Caterpillar Built Machines
Water Pump - Install
C6.6 Engines for Caterpillar Built Machines
Water Temperature Regulator - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Flywheel - Remove
24M Motor Grader Power Train Electronic Control System
MID 027 - CID 0379 - FMI 03
C6.6 Engines for Caterpillar Built Machines
Flywheel - Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft Rear Seal - Remove
C6.6 Engines for Caterpillar Built Machines
Crankshaft Rear Seal - Install
C6.6 Engines for Caterpillar Built Machines
Flywheel Housing - Remove and Install - Standard Housing
C6.6 Engines for Caterpillar Built Machines
Flywheel Housing - Remove and Install - Wet Back End Housing
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Remove - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Install - Pulleys without Split Lock Rings