Flywheel - Remove
`
C6.6 Engines for Caterpillar Built Machines
[KENR6081]
C6.6 Engines for Caterpillar Built Machines
Water Temperature Regulator - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Flywheel - Install
BASIC ENGINE
FLYWHEEL GP
C6.6 Engines for Caterpillar Built Machines
Flywheel - Remove
C6.6 Engines for Caterpillar Built Machines
Flywheel - Install
1.1. Removal Procedure
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | - | Guide Stud (1/2 inch - UNF by 4 inch) |
2 |
Start By:
- Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolts from position (X) on flywheel (1).
- Install Tooling (A) in position (X) on flywheel (1).
- Install a suitable lifting device on flywheel (1). Support the weight of the flywheel. The flywheel can weigh
71 kg (156 lb) . - If necessary, remove bolts (2) that secure the housing for pilot bearing (3) to flywheel (1). Remove the housing for pilot bearing (3).
- Remove remaining bolts (4).
- Use the lifting device to remove the flywheel from the engine.
Show/hide table
Illustration 2 g01336669 Typical example - Inspect flywheel (1) and ring gear (5) for wear or damage. Replace any worn components or damaged components.
- To remove flywheel ring gear (5), follow steps 8.a and 8.b.
- Place the flywheel assembly on a suitable support.
- Use a hammer and a punch in order to remove ring gear (5) from flywheel (1).
Note: Identify the orientation of the teeth on the flywheel ring gear.
Show/hide table
![]() | |
Illustration 1 | g01336668 |
Typical example |
Information System:
C6.6 Engines for Caterpillar Built Machines
Water Temperature Regulator - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Water Pump - Install
C6.6 Engines for Caterpillar Built Machines
Water Pump - Remove
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pump - Install
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pump - Remove
C6.6 Engines for Caterpillar Built Machines
Engine Oil Relief Valve - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
EquipmentManager Dealer Administrator Manual
Major Repair
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines
Engine Oil Filter Base - Remove and Install
24M Motor Grader Power Train Electronic Control System
MID 027 - CID 0379 - FMI 03
C6.6 Engines for Caterpillar Built Machines
Flywheel - Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft Rear Seal - Remove
C6.6 Engines for Caterpillar Built Machines
Crankshaft Rear Seal - Install
C6.6 Engines for Caterpillar Built Machines
Flywheel Housing - Remove and Install - Standard Housing
C6.6 Engines for Caterpillar Built Machines
Flywheel Housing - Remove and Install - Wet Back End Housing
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Remove - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Install - Pulleys without Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Install - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Remove - Pulleys without Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Remove and Install
770 and 772 Off-Highway Truck/Tractors
Evaporator Coil - Remove and Install