Crankshaft Rear Seal - Remove
`
C6.6 Engines for Caterpillar Built Machines
[KENR6081]
C6.6 Engines for Caterpillar Built Machines
Flywheel - Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft Rear Seal - Install
BASIC ENGINE
CRANKSHAFT GP
3408E and 3412E Engines for Caterpillar Built Machines
Bearing Clearance - Check
C6.6 Engines for Caterpillar Built Machines
Crankshaft Rear Seal - Remove
C6.6 Engines for Caterpillar Built Machines
Crankshaft Rear Seal - Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C6.6 Engines for Caterpillar Built Machines
Crankshaft - Remove
C6.6 Engines for Caterpillar Built Machines
Crankshaft - Install
1.1. Removal Procedure
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 194-3536 | T40 Torx Socket | 1 |
B | 227-4389 | E10 Torx Socket | 1 |
Start By:
- Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install" for the correct procedure.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
![]() | |
Illustration 1 | g01337506 |
Typical example |
- Use Tooling (B) in order to remove torx bolts (1) from the assembly of crankshaft rear seal (2).
- Use Tooling (A) in order to remove torx bolts (3) from the assembly of the crankshaft rear seal.
- Remove the assembly of crankshaft rear seal (2) from the cylinder block. Discard the assembly of crankshaft rear seal (2).
Note: Removal of the engine oil pan plate for the engine oil pan is not necessary in order to remove the crankshaft rear seal.
Note: The assembly of the crankshaft rear seal is nonserviceable. If the assembly of the crankshaft rear seal is removed, the assembly must be replaced.
Information System:
C6.6 Engines for Caterpillar Built Machines
Flywheel - Install
24M Motor Grader Power Train Electronic Control System
MID 027 - CID 0379 - FMI 03
C6.6 Engines for Caterpillar Built Machines
Flywheel - Remove
C6.6 Engines for Caterpillar Built Machines
Water Temperature Regulator - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Water Pump - Install
C6.6 Engines for Caterpillar Built Machines
Water Pump - Remove
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pump - Install
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pump - Remove
C6.6 Engines for Caterpillar Built Machines
Engine Oil Relief Valve - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines
Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
EquipmentManager Dealer Administrator Manual
Major Repair
C6.6 Engines for Caterpillar Built Machines
Crankshaft Rear Seal - Install
C6.6 Engines for Caterpillar Built Machines
Flywheel Housing - Remove and Install - Standard Housing
C6.6 Engines for Caterpillar Built Machines
Flywheel Housing - Remove and Install - Wet Back End Housing
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Remove - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Install - Pulleys without Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Install - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Remove - Pulleys without Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Remove and Install
770 and 772 Off-Highway Truck/Tractors
Evaporator Coil - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Front Cover - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Gear Group (Front) - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Idler Gear - Remove