Vibration Damper and Pulley - Install - Pulleys without Split Lock Rings
`
C6.6 Engines for Caterpillar Built Machines
[KENR6081]
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Remove - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Install - Pulley with Split Lock Rings
BASIC ENGINE
BELT TIGHTENER GP
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Remove - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Install - Pulleys without Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Install - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Remove - Pulleys without Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Alternator Belt - Remove and Install
1.1. Installation Procedure
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | - | Guide Stud M12 by 70 mm |
1 |
B | 227-4393 | E18 Torx Socket | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Ensure that the crankshaft adapter and the front of the crankshaft are clean and free from damage. Install crankshaft adapter (1) to the crankshaft.
- Install torx screws (5) to crankshaft adapter (1).
- Use a suitable tool in order to prevent the crankshaft from rotating. Use Tooling (B) to tighten the torx screws to a torque of
200 N·m (147 lb ft) . - Repeat Step 3 two more times in order to ensure correct torque.
- Install Tooling (A) to crankshaft adapter (1).
- Align crankshaft pulley (2) with Tooling (A). Install the crankshaft pulley to crankshaft adapter (1).
- Inspect the vibration damper for damage. If necessary, replace the vibration damper.
- Align vibration damper (3) with Tooling (A). Install the vibration damper to crankshaft adapter (1).
- Install bolts (4) to the assembly of the crankshaft pulley, the vibration damper, and the crankshaft adapter. Evenly spaced the bolts. Remove Tooling (A). Install remaining bolts (4).
- Use a suitable tool in order to prevent the crankshaft from rotating. Tighten bolts (4) to a torque of
115 N·m (85 lb ft) .
Show/hide table
![]() | |
Illustration 1 | g01337793 |
End By:
- Install the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove and Install" for the correct procedure.
Information System:
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Remove - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Flywheel Housing - Remove and Install - Wet Back End Housing
C6.6 Engines for Caterpillar Built Machines
Flywheel Housing - Remove and Install - Standard Housing
C6.6 Engines for Caterpillar Built Machines
Crankshaft Rear Seal - Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft Rear Seal - Remove
C6.6 Engines for Caterpillar Built Machines
Flywheel - Install
24M Motor Grader Power Train Electronic Control System
MID 027 - CID 0379 - FMI 03
C6.6 Engines for Caterpillar Built Machines
Flywheel - Remove
C6.6 Engines for Caterpillar Built Machines
Water Temperature Regulator - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Water Pump - Install
C6.6 Engines for Caterpillar Built Machines
Water Pump - Remove
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pump - Install
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Install - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Vibration Damper and Pulley - Remove - Pulleys without Split Lock Rings
C6.6 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Remove and Install
770 and 772 Off-Highway Truck/Tractors
Evaporator Coil - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Front Cover - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Gear Group (Front) - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Idler Gear - Remove
C6.6 Engines for Caterpillar Built Machines
Idler Gear - Install
C6.6 Engines for Caterpillar Built Machines
Housing (Front) - Remove
C6.6 Engines for Caterpillar Built Machines
Housing (Front) - Install
C6.6 Engines for Caterpillar Built Machines
Accessory Drive - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Crankcase Breather - Remove - Unfiltered Breather