C6.6 Engines for Caterpillar Built Machines Engine Oil Pan Plate - Remove and Install - Aluminum Oil Pan Caterpillar


Engine Oil Pan Plate - Remove and Install - Aluminum Oil Pan
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
194-3536  T40 Torx Socket 

Start By:

  1. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".

  2. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Dispose of all fluids according to local regulations and mandates.




    Illustration 1g01342059

  1. Remove isolating frame from the cylinder block. Follow steps 1.a through 1.c in order to remove the isolating frame from the cylinder block.

    1. Support the isolating frame (3). Use Tooling (A) to remove the torx screws (2) and (4).

    2. Remove the isolating frame (3) from the cylinder block.

    3. Remove the joint (1).

Installation Procedure

Table 2
Required Tools 
Tool  Part Number  Part Description  Qty 
194-3536  T40 Torx Socket 
Guide Stud
(M8 by 100 mm) 
Loctite 5900 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Dispose of all fluids according to local regulations and mandates.




Illustration 2g01342186
Typical example

  1. Install Tooling (B) to Positions (X) in the cylinder block.

  2. Install the isolating frame to the cylinder block. Follow Steps 2.a through 2.f in order to install the isolating frame.

    1. Ensure that the joint face of the cylinder block is clean and free from damage.

    2. Ensure that the isolating frame is clean and free from damage. If necessary, replace the isolating frame.


      Illustration 3g01342058
      Tooling (B) is not shown for clarity.

    3. Apply a bead of Tooling (C) to Positions (Y).


      Illustration 4g01342059

    4. Position a new joint (1) onto the isolating frame (3).

    5. Align the isolating frame (3) with Tooling (B). Install the isolating frame to the cylinder block.

    6. Use Tooling (A) to install the two torx screws (2) and the four torx screws (4) to the isolating frame. Tighten the torx screws (2) to a torque of 22 N·m (16 lb ft). Tighten the torx screws (4) to a torque of 22 N·m (16 lb ft).

End By:

  1. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".

  2. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".

Information System:

C6.6 Engines for Caterpillar Built Machines Engine Oil Pan - Install - Cast Iron Oil Pan
C6.6 Engines for Caterpillar Built Machines Engine Oil Pan - Install - Aluminum Oil Pan
C6.6 Engines for Caterpillar Built Machines Engine Oil Pan - Remove - Aluminum Oil Pan
C6.6 Engines for Caterpillar Built Machines Engine Oil Pan - Remove - Cast Iron Oil Pan
C6.6 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
C6.6 Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
C6.6 Engines for Caterpillar Built Machines Camshaft - Remove and Install
C6.6 Engines for Caterpillar Built Machines Lifter Group - Remove and Install
C6.6 Engines for Caterpillar Built Machines Cylinder Head - Install
C6.6 Engines for Caterpillar Built Machines Cylinder Head - Remove
C6.6 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install
C6.6 Engines for Caterpillar Built Machines Rocker Shaft - Assemble
C6.6 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
C6.6 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C6.6 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
C6.6 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
C6.6 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
C6.6 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove - Connecting rods in position
C6.6 Engines for Caterpillar Built Machines Connecting Rod Bearings - Install - Connecting rods in position
C6.6 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C6.6 Engines for Caterpillar Built Machines Crankshaft - Remove
C6.6 Engines for Caterpillar Built Machines Crankshaft - Install
C6.6 Engines for Caterpillar Built Machines Crankshaft Timing Ring - Remove and Install
C6.6 Engines for Caterpillar Built Machines Crankshaft Gear - Remove and Install