Crankshaft Timing Ring - Remove and Install
`
C6.6 Engines for Caterpillar Built Machines
[KENR6081]
C6.6 Engines for Caterpillar Built Machines
Crankshaft - Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft Gear - Remove and Install
BASIC ENGINE
CRANKSHAFT GP
3408E and 3412E Engines for Caterpillar Built Machines
Bearing Clearance - Check
C6.6 Engines for Caterpillar Built Machines
Crankshaft Rear Seal - Remove
C6.6 Engines for Caterpillar Built Machines
Crankshaft Rear Seal - Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C6.6 Engines for Caterpillar Built Machines
Crankshaft - Remove
C6.6 Engines for Caterpillar Built Machines
Crankshaft - Install
1.1. Removal Procedure
2.1. Installation Procedure
Start By:
- If a crankshaft wear sleeve is installed to the crankshaft, remove the crankshaft wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Wear Sleeve - Remove ".
- Remove the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove ".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Support crankshaft (1) on a suitable stand.
- Remove Allen head screws (2) from the crankshaft timing ring (3). Do not reuse the allen head screws.
- Carefully remove crankshaft timing ring (3) from crankshaft (1). Do not reuse the crankshaft timing ring.
Note: Ensure that seal surface (4) of the crankshaft is not damaged when the crankshaft timing ring is removed.
Note: Do not remove dowel (5) from crankshaft (1) unless the dowel is damaged.
Show/hide table
![]() | |
Illustration 1 | g01341462 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Ensure that the flange for the crankshaft timing ring on the crankshaft is clean and free from damage.
- Support crankshaft (1) on a suitable stand.
Show/hide table
Illustration 2 g01341462 - If dowel (5) was removed, install a new dowel to crankshaft (1).
- Position new crankshaft timing ring (3) on the crankshaft with the teeth toward the crankshaft web. Align the hole in crankshaft timing ring (3) with dowel (5) in the crankshaft. Carefully install crankshaft timing ring (3) to the crankshaft (1).
Note: Ensure that seal surface (4) on the crankshaft is not damaged when the crankshaft timing ring is installed.
- Install new Allen head screws (2). Tighten the Allen head screws to a torque of
9 N·m (80 lb in) .
End By:
- Install the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Install ".
- If a crankshaft wear sleeve was previously installed to the crankshaft, install a new crankshaft wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Wear Sleeve - Install".
Information System:
C6.6 Engines for Caterpillar Built Machines
Crankshaft - Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft - Remove
C6.6 Engines for Caterpillar Built Machines
Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C6.6 Engines for Caterpillar Built Machines
Connecting Rod Bearings - Install - Connecting rods in position
C6.6 Engines for Caterpillar Built Machines
Connecting Rod Bearings - Remove - Connecting rods in position
C6.6 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Install
C6.6 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Assemble
C6.6 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Disassemble
C6.6 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Remove
C6.6 Engines for Caterpillar Built Machines
Piston Cooling Jets - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pan Plate - Remove and Install - Aluminum Oil Pan
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pan - Install - Cast Iron Oil Pan
C6.6 Engines for Caterpillar Built Machines
Crankshaft Gear - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Position Sensor (Fuel Injection Pump) - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Coolant Temperature Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Fuel Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Boost Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Inlet Air Temperature Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Glow Plugs - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Alternator Belt - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Fan - Remove and Install
C6.6 Engines for Caterpillar Built Machines
ECM Mounting Bracket - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Electronic Control Module - Remove and Install