Position Sensor (Fuel Injection Pump) - Remove and Install
`
C6.6 Engines for Caterpillar Built Machines
[KENR6081]
C6.6 Engines for Caterpillar Built Machines
Crankshaft Gear - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Coolant Temperature Sensor - Remove and Install
ELECTRICAL AND STARTING SYSTEM
SENSOR GP
C6.6 Engines for Caterpillar Built Machines
Position Sensor (Fuel Injection Pump) - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Coolant Temperature Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Fuel Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Boost Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Inlet Air Temperature Sensor - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Removal Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Slide locking tab (1) into the unlocked position.
Show/hide table
![]() | |
Illustration 1 | g01341704 |
Typical example |
- Disconnect harness assembly (2) from position sensor (3) .
- Remove bolt (4) .
- Carefully remove position sensor (3) from the fuel injection pump.
Note: Do not use a lever to remove the position sensor from the fuel injection pump.
- Plug the hole for the position sensor in the fuel injection pump with a new plug.
- Remove O-ring seal (5) from position sensor (3) .
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Lubricate a new O-ring seal (5) with clean engine oil. Install the new O-ring seal into the first groove in position sensor (3) .
Show/hide table
![]() | |
Illustration 2 | g01341704 |
Typical example |
- Remove the plug from the hole in the fuel injection pump for the position sensor.
- Align the hole in position sensor (3) with the hole in the fuel injection pump. Install the position sensor to the fuel injection pump.
Note: Do not use bolt (4) to pull the position sensor into position against the fuel injection pump.
- Install bolt (4) . Tighten the bolt to a torque of 14 N·m (10 lb ft).
- Connect harness assembly (2) to position sensor (3) .
- Slide locking tab (1) into the locked position.
Information System:
C6.6 Engines for Caterpillar Built Machines
Crankshaft Gear - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft Timing Ring - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft - Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft - Remove
C6.6 Engines for Caterpillar Built Machines
Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C6.6 Engines for Caterpillar Built Machines
Connecting Rod Bearings - Install - Connecting rods in position
C6.6 Engines for Caterpillar Built Machines
Connecting Rod Bearings - Remove - Connecting rods in position
C6.6 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Install
C6.6 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Assemble
C6.6 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Disassemble
C6.6 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Remove
C6.6 Engines for Caterpillar Built Machines
Piston Cooling Jets - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Coolant Temperature Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Fuel Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Boost Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Inlet Air Temperature Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Glow Plugs - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Alternator Belt - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Fan - Remove and Install
C6.6 Engines for Caterpillar Built Machines
ECM Mounting Bracket - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Electronic Control Module - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Electric Starting Motor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Air Compressor - Remove and Install