Engine Oil Pressure Sensor - Remove and Install
`
C6.6 Engines for Caterpillar Built Machines
[KENR6081]
C6.6 Engines for Caterpillar Built Machines
Coolant Temperature Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Fuel Pressure Sensor - Remove and Install
ELECTRICAL AND STARTING SYSTEM
SENSOR GP
C6.6 Engines for Caterpillar Built Machines
Position Sensor (Fuel Injection Pump) - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Coolant Temperature Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Fuel Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Boost Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Inlet Air Temperature Sensor - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. |
- Slide locking tab (1) into the unlocked position.
- Disconnect harness assembly (2) from engine oil pressure sensor (3).
- Use a deep socket to remove engine oil pressure sensor (3) from the cylinder block.
- Remove O-ring seal (4) from engine oil pressure sensor (3).
Show/hide table
![]() | |
Illustration 1 | g01341698 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Lubricate a new O-ring seal (4) with clean engine oil. Install the new O-ring seal onto engine oil pressure sensor (3).
- Use a deep socket to install engine oil pressure sensor (3) to the cylinder block. Tighten the engine oil pressure sensor to a torque of
10 N·m (89 lb in) . - Connect harness assembly (2) to engine oil pressure sensor (3).
- Slide locking tab (1) into the locked position.
- If necessary, fill the engine oil pan to the correct level that is indicated on the engine oil level gauge. Refer to Operation and Maintenance Manual, "Engine Oil Level - Check".
Show/hide table
![]() | |
Illustration 2 | g01341698 |
Information System:
C6.6 Engines for Caterpillar Built Machines
Coolant Temperature Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Position Sensor (Fuel Injection Pump) - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft Gear - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft Timing Ring - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft - Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft - Remove
C6.6 Engines for Caterpillar Built Machines
Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C6.6 Engines for Caterpillar Built Machines
Connecting Rod Bearings - Install - Connecting rods in position
C6.6 Engines for Caterpillar Built Machines
Connecting Rod Bearings - Remove - Connecting rods in position
C6.6 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Install
C6.6 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Assemble
C6.6 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Disassemble
C6.6 Engines for Caterpillar Built Machines
Fuel Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Boost Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Inlet Air Temperature Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Glow Plugs - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Alternator Belt - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Fan - Remove and Install
C6.6 Engines for Caterpillar Built Machines
ECM Mounting Bracket - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Electronic Control Module - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Electric Starting Motor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Air Compressor - Remove and Install
24M Motor Grader Power Train Electronic Control System
Using Messenger to Determine Diagnostic Codes
3412E Engine for Caterpillar Built Machines
Cat Data Link - Test