Inlet Air Temperature Sensor - Remove and Install
`
C6.6 Engines for Caterpillar Built Machines
[KENR6081]
C6.6 Engines for Caterpillar Built Machines
Boost Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Glow Plugs - Remove and Install
ELECTRICAL AND STARTING SYSTEM
SENSOR GP
C6.6 Engines for Caterpillar Built Machines
Position Sensor (Fuel Injection Pump) - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Coolant Temperature Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Fuel Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Boost Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Inlet Air Temperature Sensor - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Slide locking tab (1) into the unlocked position.
- Disconnect harness assembly (2) from inlet air temperature sensor (3).
Note: The inlet air temperature sensor has a two wire plug.
- Use a deep socket in order to remove inlet air temperature sensor (3) from the inlet manifold.
- Remove O-ring seal (4) from inlet air temperature sensor (3).
Show/hide table
![]() | |
Illustration 1 | g01341729 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Lubricate a new O-ring seal (4) with clean engine oil. Install the new O-ring seal onto the inlet air temperature sensor.
- Install inlet air temperature sensor (3) to the inlet manifold. Use a deep socket in order to tighten the inlet air temperature sensor to a torque of
20 N·m (15 lb ft) . - Connect harness assembly (2) to inlet air temperature sensor (3).
- Slide locking tab (1) into the locked position.
Show/hide table
![]() | |
Illustration 2 | g01341729 |
Information System:
C6.6 Engines for Caterpillar Built Machines
Boost Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Fuel Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Engine Oil Pressure Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Coolant Temperature Sensor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Position Sensor (Fuel Injection Pump) - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft Gear - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft Timing Ring - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft - Install
C6.6 Engines for Caterpillar Built Machines
Crankshaft - Remove
C6.6 Engines for Caterpillar Built Machines
Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C6.6 Engines for Caterpillar Built Machines
Connecting Rod Bearings - Install - Connecting rods in position
C6.6 Engines for Caterpillar Built Machines
Connecting Rod Bearings - Remove - Connecting rods in position
C6.6 Engines for Caterpillar Built Machines
Glow Plugs - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Alternator Belt - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Fan - Remove and Install
C6.6 Engines for Caterpillar Built Machines
ECM Mounting Bracket - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Electronic Control Module - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Electric Starting Motor - Remove and Install
C6.6 Engines for Caterpillar Built Machines
Air Compressor - Remove and Install
24M Motor Grader Power Train Electronic Control System
Using Messenger to Determine Diagnostic Codes
3412E Engine for Caterpillar Built Machines
Cat Data Link - Test
2007/07/09
Acceptable Gap Between Lift Arm and Stop Block on Skid Steer Loaders and Multi Terrain Loaders {6119, 7050}
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train
Track Drive - Install
587R Pipelayer Machine Systems
Accumulator - Remove and Install