160M and 160 Motor Grader Machine Systems Bank Valve - Remove - Rear Frame Caterpillar


Bank Valve - Remove - Rear Frame
`
1.1. Removal Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
311-1362  Vacuum Cap 
138-7575  Link Bracket 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.


Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.

  1. Lower the blade to the ground.

  2. Release the system pressure. Refer to Operation and Maintenance Manual, "System Pressure - Release".


    Illustration 1g01392655

  3. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A). Apply 138 kPa (20 psi). This procedure will pull a vacuum on the hydraulic system.


    Illustration 2g01392674

  4. Remove bolts (2). Repeat for the opposite side of the machine.

  5. Remove cover (1) from the machine.


    Illustration 3g01360710

  6. Disconnect tube assembly (3). Disconnect fitting (4). Disconnect harness assemblies (5).


    Illustration 4g01360753

  7. Disconnect tube assembly (6). Disconnect fitting (7). Disconnect harness assemblies (8).


    Illustration 5g01361045

  8. Disconnect tube assemblies (9).


    Illustration 6g01392685

  9. Remove tube assemblies (10). Disconnect hose assemblies (11). Remove tube assemblies (12). Disconnect hose assembly (13). Disconnect hose assembly (14).


    Illustration 7g01392707

  10. Disconnect harness assembly (15). Remove bolts (16) in order to remove harness assembly (15) from support (17).


    Illustration 8g01392715

  11. Remove nuts (18). Remove bolt (19) and spacer (20).


    Illustration 9g01393956

  12. Remove bolts (21) and remove spacers (22). Reposition support (23).


    Illustration 10g01393961

  13. Disconnect tube assemblies (24).


    Illustration 11g01393996


    Illustration 12g01394033

  14. Remove bolts (25).


    Illustration 13g01394034

  15. Use Tooling (B) and a suitable lifting device in order to remove bank valve (26). The weight of bank valve (26) is approximately 50 kg (110 lb).

Information System:

259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Idler Axle - Disassemble
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 157 - CID 0967 - FMI 02
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 156 - CID 0967 - FMI 02
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 082 - CID 0967 - FMI 02
2007/07/09 New Installation Sleeves for the Transmission Clutches Are Now Available {0720, 3030, 3155}
C6.6 Engines for Caterpillar Built Machines Fuel Priming Pump - Remove and Install - Electric Fuel Priming Pump
AP655D and BG655D Asphalt Pavers Propel System Piston Pump (Propel) - Steel Track Machine
24M Motor Grader Power Train Transmission Lubrication
AP655D and BG655D Asphalt Pavers Propel System Location of Hydraulic Components (Propel System) - Steel Track Machine
3412E Engine for Caterpillar Built Machines Timing - Calibrate
AP655D and BG655D Asphalt Pavers Propel System General Information (Propel System) - Steel Track Machine
C15 and C18 Generator Set Engines Radiator Core - Remove and Install - Charge Air
AP655D and BG655D Asphalt Pavers Propel System Piston Motor (Propel) - Steel Track Machine
C15 and C18 Generator Set Engines Radiator Top Tank - Remove and Install - Charge Air
2007/07/02 New Routing of Wiring Harness for Pressure Sensor {1408, 5057, 6543}
C15 and C18 Generator Set Engines Radiator Bottom Tank - Remove and Install - Charge Air
2007/08/06 Radiator and Hydraulic Oil Coolers Have Been Improved {1351}
C4.4 and C6.6 Engines for Caterpillar Built Machines Low Power/Poor or No Response to Throttle
C4.4 and C6.6 Engines for Caterpillar Built Machines Diagnostic Code Cross Reference
AP655D and BG655D Asphalt Pavers Propel System Hydraulic Schematic (Propel System) - Steel Track Machine
587R Pipelayer Machine Systems Boom Winch, Hook Winch and Winch Frame - Remove
587R Pipelayer Machine Systems Boom Winch, Hook Winch and Winch Frame - Install
The Fitting on the Air Cleaner Group is Installed Incorrectly on Specific Off-Highway Trucks{1051}
CB14 Paving Compactor Machine Systems Piston Pump (Propel) - Disassemble