587R Pipelayer Machine Systems Boom Winch, Hook Winch and Winch Frame - Remove Caterpillar


Boom Winch, Hook Winch and Winch Frame - Remove
`
1.1. Removal Procedure

Removal Procedure

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     189-0410     Shackle As     2    
1U-9204 Lever Puller Hoist     1    
138-7576 Link Bracket     1    

Start By:

  1. Remove the lower boom sheave block. Refer to Disassembly and Assembly, "Lower Boom Sheave Block - Remove and Install".
  2. Remove the lower load sheave block. Refer to Disassembly and Assembly, "Lower Sheave Block - Remove and Install".

  1. Lower the counterweight frame.

  1. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".

  1. Drain the hydraulic tank into a suitable container for proper storage or disposal.



    Illustration 1g01364696

  1. Remove covers (1) and (2) .



    Illustration 2g01392889

  1. Disconnect hose assemblies (3) .



    Illustration 3g01392914

  1. Position accumulator (4) out of the way.



    Illustration 4g01364720

  1. Disconnect hose assemblies (5), (6), and (7) .



    Illustration 5g01364721

  1. Disconnect hose assemblies (8), (9), and (10) .



    Illustration 6g01364722

  1. Remove bolts (11). Position filter base (12) out of the way.



    Illustration 7g01364724

  1. Disconnect hose assemblies (13), (14), and (15) .



    Illustration 8g01364726

  1. Disconnect hose assemblies (16), (17), (18), and (19) .



    Illustration 9g01364727

  1. Disconnect hose assemblies (20), (21), and (22) .



    Illustration 10g01364730

  1. Attach Tooling (A) and a suitable lifting device onto boom winch, hook winch and winch frame (23). The weight of boom winch, hook winch and winch frame (23) is approximately 2767 kg (6100 lb).



    Illustration 11g01364731

  1. Remove bolts (24). Remove winch (23) .

Information System:

AP655D and BG655D Asphalt Pavers Propel System Hydraulic Schematic (Propel System) - Steel Track Machine
C4.4 and C6.6 Engines for Caterpillar Built Machines Diagnostic Code Cross Reference
C4.4 and C6.6 Engines for Caterpillar Built Machines Low Power/Poor or No Response to Throttle
2007/08/06 Radiator and Hydraulic Oil Coolers Have Been Improved {1351}
C15 and C18 Generator Set Engines Radiator Bottom Tank - Remove and Install - Charge Air
2007/07/02 New Routing of Wiring Harness for Pressure Sensor {1408, 5057, 6543}
C15 and C18 Generator Set Engines Radiator Top Tank - Remove and Install - Charge Air
AP655D and BG655D Asphalt Pavers Propel System Piston Motor (Propel) - Steel Track Machine
160M and 160 Motor Grader Machine Systems Bank Valve - Remove - Rear Frame
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Idler Axle - Disassemble
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 157 - CID 0967 - FMI 02
AP600D, AP655D, BG600D and BG655D Asphalt Pavers MID 156 - CID 0967 - FMI 02
587R Pipelayer Machine Systems Boom Winch, Hook Winch and Winch Frame - Install
The Fitting on the Air Cleaner Group is Installed Incorrectly on Specific Off-Highway Trucks{1051}
CB14 Paving Compactor Machine Systems Piston Pump (Propel) - Disassemble
CB14 Paving Compactor Machine Systems Piston Pump (Propel) - Assemble
Reworking the Pressure Sensor for the Saw Pump{1408, 5057, 6543}
3412E Engine for Caterpillar Built Machines Coolant Flow - Test
587R Pipelayer Machine Systems Boom - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Cooling Fan Control - Test
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Control Valve (Tilt)
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Control Valve (Lift)
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Control Valve (Auxiliary)
R1600G Load Haul Dump Remote Control System General Information