Main Control Valve - Assemble
`
587R Pipelayer Machine Systems
[RENR8212]
587R Pipelayer Machine Systems
Main Control Valve - Disassemble
587R Pipelayer Machine Systems
Pilot Control Valve - Remove - Load, Boom, and Counterweight
HYDRAULIC SYSTEM
VALVE GP-CONTROL
587R Pipelayer Machine Systems
Main Control Valve - Remove
587R Pipelayer Machine Systems
Main Control Valve - Install
587R Pipelayer Machine Systems
Main Control Valve - Disassemble
587R Pipelayer Machine Systems
Main Control Valve - Assemble
1.1. Assembly Procedure
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install O-ring seal (54), O-ring seal (53), and backup ring (52) to check valve (44). Note the orientation of piston (45) for installation purposes.
Show/hide table
![]() | |
Illustration 1 | g01244123 |
- Install O-ring seal (51), O-ring seal (50), and backup ring (49) to check valve (43) .
Show/hide table
![]() | |
Illustration 2 | g01244122 |
- Install O-ring seal (48), O-ring seals (47), and backup rings (46) to boom brake release valve (41) .
Show/hide table
![]() | |
Illustration 3 | g01244121 |
- Repeat Step 3 for hook brake release valve (42). Refer to Illustration 4.
- Install piston (45), check valve (44), and check valve (43). Tighten check valves (43) and (44) to a torque of 31 ± 3 N·m (23 ± 2 lb ft).
Show/hide table
![]() | |
Illustration 4 | g01393491 |
- Install boom brake release valve (41) and hook brake release valve (42). Tighten boom brake release valve (41) and hook brake release valve to a torque of 31 ± 3 N·m (23 ± 2 lb ft).
- Install O-ring seal (40), O-ring seals (39), and backup rings (38) to boom interlock valve (8) .
Show/hide table
![]() | |
Illustration 5 | g01244118 |
- Repeat Step 7 for hook interlock valve (10). Refer to Illustration 12.
- Install O-ring seal (37), O-ring seals (36), and backup rings (35) to shuttle valve (7) .
Show/hide table
![]() | |
Illustration 6 | g01244117 |
- Repeat Step 9 for shuttle valve (9). Refer to Illustration 12.
- Install coil assembly (33), nut (34), O-ring seal (32), O-ring seals (31), and backup rings (30) to boom kickout valve (6). Tighten nut (34) to a torque of 5.3 ± 1.5 N·m (47 ± 13 lb in).
Show/hide table
![]() | |
Illustration 7 | g01244115 |
- Install coil assembly (28), nut (29), O-ring seal (27), screen (26), O-ring seal (25), and backup ring (24) to pilot shutoff valve (4). Tighten nut (29) to a torque of 5.3 ± 1.5 N·m (47 ± 13 lb in).
Show/hide table
![]() | |
Illustration 8 | g01244113 |
- Install O-ring seal (23), backup ring (22), and O-ring seal (21) to pilot relief valve (3) .
Show/hide table
![]() | |
Illustration 9 | g01244112 |
- Install coil assembly (19), nut (20), O-ring seal (18), O-ring seals (17), and backup rings (16) to dead engine hook lowering valve (2). Tighten nut (20) to a torque of 5.3 ± 1.5 N·m (47 ± 13 lb in).
Show/hide table
![]() | |
Illustration 10 | g01244110 |
- Repeat Step 14 for dead engine boom lowering valve (5). Refer to Illustration 12.
- Install coil assembly (14), nut (15), O-ring seal (13), O-ring seal (12), and backup ring (11) to charging valve (1). Tighten nut (15) to a torque of 5.3 ± 1.5 N·m (47 ± 13 lb in).
Show/hide table
![]() | |
Illustration 11 | g01244109 |
- Install boom interlock valve (8) and hook interlock valve (10). Tighten boom interlock valve (8) and hook interlock valve (10) to a torque of 31 ± 3 N·m (23 ± 2 lb ft).
Show/hide table
![]() | |
Illustration 12 | g01393481 |
- Install shuttle valves (7) and (9). Tighten shuttle valves (7) and (9) to a torque of 24 ± 3 N·m (18 ± 2 lb ft).
- Install boom kickout valve (6), dead engine boom lowering valve (5), and dead engine hook lowering valve (2). Tighten boom kickout valve (6), dead engine boom lowering valve (5), and dead engine hook lowering valve (2) to a torque of 24 ± 3 N·m (18 ± 2 lb ft).
- Install pilot shutoff valve (4), pilot relief valve (3), and charging valve (1). Tighten pilot shutoff valve (4), pilot relief valve (3), and charging valve (1) to a torque of 31 ± 3 N·m (23 ± 2 lb ft).
End By: Install the main control valve. Refer to Disassembly and Assembly, "Main Control Valve - Install".
Information System:
3412E Engine for Caterpillar Built Machines
Electrical Power Supply - Test
587R Pipelayer Machine Systems
Main Control Valve - Disassemble
24M Motor Grader Power Train
Transmission Hydraulic Control
EquipmentManager Dealer Administrator Manual
Fault Codes
587R Pipelayer Machine Systems
Main Control Valve - Install
587R Pipelayer Machine Systems
Main Control Valve - Remove
3412E Engine for Caterpillar Built Machines
Cooling Fan Speed - Test
R1600G Load Haul Dump Remote Control System
Machine Preparation for Troubleshooting
R1600G Load Haul Dump Remote Control System
Control Valve (Steering and Bucket)
R1600G Load Haul Dump Remote Control System
General Information
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System
Control Valve (Auxiliary)
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System
Control Valve (Lift)
24M Motor Grader Hydraulic and Steering System
Implement System
R1600G Load Haul Dump Power Train
Machine Preparation for Troubleshooting
R1600G Load Haul Dump Steering System
Steering System Troubleshooting
R1600G Load Haul Dump Steering System
System Pressure - Release
R1600G Load Haul Dump Steering System
Steering System Pressure - Test and Adjust
R1600G Load Haul Dump Braking System
System Pressure - Release
R1600G Load Haul Dump Power Train Electronic Control System
Power Train Electronic Control System
R1600G Load Haul Dump Power Train Electronic Control System
Autoshift Control
R1600G Load Haul Dump Power Train Electronic Control System
Electronic Control Module (Power Train)
R1600G Load Haul Dump Power Train Electronic Control System
Switches
R1600G Load Haul Dump Hydraulic System
System Pressure - Release
R1600G Load Haul Dump 3176C Engine Supplement
System Pressure - Release