587R Pipelayer Machine Systems Pilot Control Valve - Remove - Load, Boom, and Counterweight Caterpillar


Pilot Control Valve - Remove - Load, Boom, and Counterweight
`
1.1. Removal Procedure

Removal Procedure

Start By:

  1. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "System Pressure - Release".
  2. Remove the seat. Refer to Disassembly and Assembly, "Seat - Remove and Install".

Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.

Note: Put identification marks on all lines, on all hoses, on all harness assemblies, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on AVSpare products.

Dispose of all fluids according to local regulations and mandates.


------ WARNING! ------

Personal injury can result from hydraulic oil pressure and hot oil.

Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.

Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.

----------------------



    Illustration 1g01234616

  1. Remove bolts (1) and armrest (2) .

  1. Remove covers (3) and (4) .



    Illustration 2g01234620

  1. Disconnect hose assemblies (5) .



    Illustration 3g01393802

  1. Remove rod assemblies (6), (7), and (8) .

  1. Remove bolts (9) and reposition cover (10) .



    Illustration 4g01393806

  1. Disconnect harness assemblies (11) and remove cover (10). Remove bolts (12) .



    Illustration 5g01234624

  1. Remove valve assembly (13) .

Information System:

Bench Test Procedure for a 14L, 120M, 120M Series 2, 12M, 12M Series 2, 12M Series 3, 140M, 140M Series 2, 140M Series 3, 160M, 160M Series 2, and 160M Series 3 Motor Grader Transmission {3030, 3073}
120K Motor Grader Capacities (Refill)
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Relief Valve (Line)
120K Motor Grader Tire Shipping Pressure
2007/07/23 Troubleshooting the Rotary Switch Assembly for the Engine Speed {1408, 7332}
2008/02/11 An Improved Exhaust Piping Is Now Used on Track Skidders {1061, 1062}
120K Motor Grader Lifting and Tying Down the Machine
2007/11/19 Improvement to the Governor Control Groups {1265, 1276}
3408E and 3412E Engines for the 844 Wheel Dozer and for 988F Series II and 990 Series II Wheel Loaders Ether Starting Aid - Test
120K Motor Grader Specifications
CS-563E, CP-563E, CS-573E, CP-573E, CS-583E, CP-583E, CS-663E, CP-663E and CS-683E Vibratory Soil Compactors Additional Messages
R1600G Load Haul Dump 3176C Engine Supplement System Pressure - Release
587R Pipelayer Machine Systems Pilot Control Valve - Install - Load, Boom and Counterweight
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Ride Control Valve (2-Function, 3-Function Control Valve)
R1600G Load Haul Dump Power Train Torque Converter and Updrive
R1600G Load Haul Dump Machine Electrical System Circuit Breaker
R1600G Load Haul Dump Steering System Articulated Hitch
R1600G Load Haul Dump Power Train Output Transfer Gears - Adjust
C4.4 and C6.6 Engines for Caterpillar Built Machines Event Codes
C4.4 and C6.6 Engines for Caterpillar Built Machines E360 Low Engine Oil Pressure
C18 Engine for Caterpillar Built Machines Component Location
R1600G Load Haul Dump Power Train Differential Pinion Preload - Adjust
R1600G Load Haul Dump Power Train Differential Backlash and Bearings - Adjust
R1600G Load Haul Dump Braking System Brake Release System