Pilot Control Valve - Install - Load, Boom and Counterweight
`
587R Pipelayer Machine Systems
[RENR8212]
587R Pipelayer Machine Systems
Pilot Control Valve - Remove - Load, Boom, and Counterweight
587R Pipelayer Machine Systems
Cooler Bypass Valve - Remove and Install
HYDRAULIC SYSTEM
VALVE GP-PILOT
587R Pipelayer Machine Systems
Pilot Control Valve - Disassemble
587R Pipelayer Machine Systems
Pilot Control Valve - Assemble
587R Pipelayer Machine Systems
Pilot Control Valve - Remove - Load, Boom, and Counterweight
587R Pipelayer Machine Systems
Pilot Control Valve - Install - Load, Boom and Counterweight
1.1. Installation Procedure
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install valve assembly (13) and bolts (12) .
Show/hide table
![]() | |
Illustration 1 | g01234624 |
Show/hide table
![]() | |
Illustration 2 | g01393806 |
- Position cover (10) and connect harness assemblies (11) .
- Reposition cover (10) and install bolts (9) .
Show/hide table
![]() | |
Illustration 3 | g01234621 |
- Install rod assemblies (6), (7), and (8) .
- Connect hose assemblies (5) .
Show/hide table
![]() | |
Illustration 4 | g01234620 |
- Install covers (3) and (4) .
Show/hide table
![]() | |
Illustration 5 | g01234616 |
- Install armrest (2) and bolts (1) .
End By: Install the seat. Refer to Disassembly and Assembly, "Seat - Remove and Install".
Information System:
587R Pipelayer Machine Systems
Pilot Control Valve - Remove - Load, Boom, and Counterweight
Bench Test Procedure for a 14L, 120M, 120M Series 2, 12M, 12M Series 2, 12M Series 3, 140M, 140M Series 2, 140M Series 3, 160M, 160M Series 2, and 160M Series 3 Motor Grader Transmission {3030, 3073}
120K Motor Grader
Capacities (Refill)
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System
Relief Valve (Line)
120K Motor Grader
Tire Shipping Pressure
2007/07/23
Troubleshooting the Rotary Switch Assembly for the Engine Speed {1408, 7332}
2008/02/11
An Improved Exhaust Piping Is Now Used on Track Skidders {1061, 1062}
120K Motor Grader
Lifting and Tying Down the Machine
2007/11/19
Improvement to the Governor Control Groups {1265, 1276}
3408E and 3412E Engines for the 844 Wheel Dozer and for 988F Series II and 990 Series II Wheel Loaders
Ether Starting Aid - Test
120K Motor Grader
Specifications
CS-563E, CP-563E, CS-573E, CP-573E, CS-583E, CP-583E, CS-663E, CP-663E and CS-683E Vibratory Soil Compactors
Additional Messages
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System
Ride Control Valve (2-Function, 3-Function Control Valve)
R1600G Load Haul Dump Power Train
Torque Converter and Updrive
R1600G Load Haul Dump Machine Electrical System
Circuit Breaker
R1600G Load Haul Dump Steering System
Articulated Hitch
R1600G Load Haul Dump Power Train
Output Transfer Gears - Adjust
C4.4 and C6.6 Engines for Caterpillar Built Machines
Event Codes
C4.4 and C6.6 Engines for Caterpillar Built Machines
E360 Low Engine Oil Pressure
C18 Engine for Caterpillar Built Machines
Component Location
R1600G Load Haul Dump Power Train
Differential Pinion Preload - Adjust
R1600G Load Haul Dump Power Train
Differential Backlash and Bearings - Adjust
R1600G Load Haul Dump Braking System
Brake Release System
R1600G Load Haul Dump Braking System
General Information