160M and 160 Motor Grader Machine Systems Bank Valve - Install - Rear Frame Caterpillar


Bank Valve - Install - Rear Frame
`
1.1. Installation Procedure

Installation Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
A  311-1362  Vacuum Cap 
B  138-7575  Link Bracket 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g01394034

  1. Use Tooling (B) and a suitable lifting device in order to install bank valve (26). The weight of bank valve (26) is approximately 50 kg (110 lb).


    Illustration 2g01393996


    Illustration 3g01394033

  2. Install bolts (25).


    Illustration 4g01393961

  3. Connect tube assemblies (24).


    Illustration 5g01393956

  4. Position support (23). Install spacers (22) and bolts (21).


    Illustration 6g01392715

  5. Install spacer (20) and bolt (19). Install nuts (18).


    Illustration 7g01392707

  6. Position harness assembly (15) to support (17). Install bolts (16). Connect harness assembly (15).


    Illustration 8g01392685

  7. Connect hose assembly (14). Connect hose assembly (13). Install tube assemblies (12). Connect hose assemblies (11). Install tube assemblies (10).


    Illustration 9g01361045

  8. Connect tube assemblies (9).


    Illustration 10g01360753

  9. Connect harness assemblies (8). Connect fitting (7). Connect tube assembly (6).


    Illustration 11g01360710

  10. Connect harness assemblies (5). Connect fitting (4). Connect tube assembly (3).


    Illustration 12g01392674

  11. Position cover (1) and install bolts (2) on each side of cover (1).


    Illustration 13g01392655

  12. Remove Tooling (A).

  13. Fill the hydraulic tank. Refer to Operation and Maintenance Manual, "Capacities - Refill".

Information System:

C4.4 and C6.6 Engines for Caterpillar Built Machines E539 High Intake Manifold Air Temperature
C4.4 and C6.6 Engines for Caterpillar Built Machines E361 High Engine Coolant Temperature
R1600G Load Haul Dump Braking System Service and Parking Brake System
R1600G Load Haul Dump Braking System General Information
R1600G Load Haul Dump Braking System Brake Release System
R1600G Load Haul Dump Power Train Differential Backlash and Bearings - Adjust
R1600G Load Haul Dump Power Train Differential Pinion Preload - Adjust
C18 Engine for Caterpillar Built Machines Component Location
C4.4 and C6.6 Engines for Caterpillar Built Machines E360 Low Engine Oil Pressure
C4.4 and C6.6 Engines for Caterpillar Built Machines Event Codes
R1600G Load Haul Dump Power Train Output Transfer Gears - Adjust
R1600G Load Haul Dump Steering System Articulated Hitch
3412E Engine for Caterpillar Built Machines Injection Actuation Pressure Control Valve - Test
C4.4 and C6.6 Engines for Caterpillar Built Machines 5 Volt Sensor Supply Circuit - Test
140M and 150 Motor Grader Power Train Transmission - Assemble
216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders, 247B3 and 257B3 Multi Terrain Loaders and 259B3 Compact Track Loader Sprocket - Inspect
247B2 and 257B2 Multi Terrain Loaders Caterpillar Approved Work Tools
C4.4 and C6.6 Engines for Caterpillar Built Machines CAN Data Link Circuit - Test
C18 Engine for Caterpillar Built Machines Diagnostic Trouble Code List
3412E Engine for Caterpillar Built Machines Injector Solenoid - Test
24M Motor Grader Implement Electronic Control System MID 082 - CID 2252 - FMI 02
C18 Engine for Caterpillar Built Machines Event Code List
24M Motor Grader Implement Electronic Control System MID 082 - CID 2252 - FMI 03
2007/07/16 A New Update to CAES v3.1 Software Is Now Available {7490, 7620}