Vibration Damper - Remove and Install
`
3524B Engine for Caterpillar Built Machines
[RENR2276]
3524B Engine for Caterpillar Built Machines
Exhaust Manifold - Remove and Install
3524B Engine for Caterpillar Built Machines
Fuel Priming Pump - Remove and Install
BASIC ENGINE
DAMPER GP
3524B Engine for Caterpillar Built Machines
Vibration Damper - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 6V-2078 | Stud | 2 |
B | 138-7573 | Link Bracket | 2 |
Start By:
- Remove the coupling. Refer to Disassembly and Assembly, "Coupling - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove two bolts (1) and install Tooling (A). Remove remaining bolts (1).
Show/hide table
Illustration 3 g00912786 - Attach a suitable lifting device to shaft (2). Remove shaft (2) from damper (3). The weight of shaft (2) is approximately
32 kg (70 lb) .Show/hide tableIllustration 4 g00912787 - Attach Tooling (B) to damper (3) and a suitable lifting device. Remove Tooling (A). Remove damper (3). The weight of damper (3) is approximately
204 kg (450 lb) .
Show/hide table
![]() | |
Illustration 1 | g00912784 |
Show/hide table
![]() | |
Illustration 2 | g00912785 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 6V-2078 | Stud | 2 |
B | 138-7573 | Link Bracket | 2 |
C | 6V-7820 | Torque Multiplier Gp | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Attach Tooling (B) to damper (3) and a suitable lifting device. The weight of damper (3) is approximately
204 kg (450 lb) . Position damper (3) to crankshaft (5). Timing mark (X) that is located on damper (3) must be aligned with timing mark (Y) that is located on crankshaft (5). - Install Tooling (A) and remove Tooling (B).
Show/hide table
Illustration 7 g00912786 Show/hide tableIllustration 8 g00912791 - Attach a suitable lifting device to shaft (2) and position shaft (3) to damper (3). The weight of shaft (2) is approximately
32 kg (70 lb) . Timing mark (Z) that is located on shaft (2) must be aligned with timing mark (X) (not shown) that is located on damper (3).Show/hide tableIllustration 9 g00912785 Show/hide tableIllustration 10 g00912784 - Install bolts (1). Remove Tooling (A) and install remaining bolts (1).
Show/hide table
Illustration 11 g00912792 - Use Tooling (C) in order to tighten bolts (1) to a torque of
1125 ± 100 N·m (830 ± 74 lb ft) .
Show/hide table
![]() | |
Illustration 5 | g00912787 |
Show/hide table
![]() | |
Illustration 6 | g00912790 |
End By:
- Install the coupling. Refer to Disassembly and Assembly, "Coupling - Remove and Install".
Information System:
R1600G Load Haul Dump Hydraulic System
Relief Valve (Line) - Test and Adjust
R1600G Load Haul Dump Hydraulic System
Relief Valve (Main) - Test and Adjust
R1600G Load Haul Dump Steering System
Neutralizer Valve (Implement and Steering) - Test and Adjust
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders
Operational Checks (Brake, Hydraulic Fan System)
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders
Operational Checks (Power Train)
A Procedure for Installation of the Rotor Drive is Available{5611}
3524B Engine for Caterpillar Built Machines
Exhaust Manifold - Remove and Install
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System
MID 028 - CID 0605 - FMI 02
784C and 785C Off-Highway Truck/Tractors Steering System
Steering Accumulator - Test and Charge
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System
Main Control Valve - Integrated Toolcarrier
Installation and Operation of the Caterpillar Messenger Driver Information Display{7490}
797 Off-Highway Truck Engine Supplement
Fuel Transfer Pump - Install
226 and 242 Skid Steer Loaders Power Train
Solenoid Valve and Mounting (Parking Brake) - Remove and Install
226 and 242 Skid Steer Loaders Power Train
Tire and Rim - Remove and Install
814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Machine Systems
Cab - Remove
226 and 242 Skid Steer Loaders Power Train
Axle - Remove
226 and 242 Skid Steer Loaders Power Train
Axle - Disassemble
226 and 242 Skid Steer Loaders Power Train
Axle - Assemble
226 and 242 Skid Steer Loaders Power Train
Axle - Install
814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Machine Systems
Hydraulic Tank - Disassemble
814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Machine Systems
Hydraulic Tank - Assemble
814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Machine Systems
Cab - Install
D350E Series II and D400E Series II Articulated Trucks Power Train
Solenoid Valve (Lockup Clutch)
789C Off-Highway Truck Steering System
Steering Accumulator - Test and Charge