226 and 242 Skid Steer Loaders Power Train Axle - Disassemble Caterpillar


Axle - Disassemble
`
1.1. Disassembly Procedure

Disassembly Procedure

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1P-5546     Crossblock     1    
8B-7550 Leg     2    
3H-0465 Puller Plate     4    
5F-7379 Forcing Bolt     1    
4C-5660 Adapter     2    
5B-0637 Nut     2    
8T-1757 Nut     2    
9X-8268 Washers     2    
B     6V-3009     Crossblock     1    
126-7179 Leg     2    
126-7181 Puller Plate     4    
6V-4832 Screw     1    
8H-0663 Bearing Puller     1    

Start By:

  1. Remove the axle. Refer to Disassembly and Assembly, "Axle - Remove ".


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on AVSpare products.

Dispose of all fluids according to local regulations and mandates.


Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected at all times.




    Illustration 1g00913174

  1. Use Tooling (A) to release shaft (1) from axle housing (2) .



    Illustration 2g00682603

  1. Remove spacer (3). Remove the shaft from the housing.



    Illustration 3g00682610

  1. Remove seal (4) .

  1. Remove bearing (5) .



    Illustration 4g00913175

  1. Use Tooling (B) to remove bearing (6) .

  1. Remove seal (7) .



    Illustration 5g00682622

  1. Remove bearing cup (8). Remove bearing cup (9) .



    Illustration 6g00682639

    (2) Axle Housing

    (4) Lip Type Seal

    (5) Roller Bearing

    (6) Roller Bearing

    (7) Lip Type Seal

    (8) Bearing Cup

    (9) Bearing Cup

  1. Illustration 6 shows the location of the components that are in the axle assembly.

Information System:

226 and 242 Skid Steer Loaders Power Train Axle - Remove
814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Machine Systems Cab - Remove
226 and 242 Skid Steer Loaders Power Train Tire and Rim - Remove and Install
226 and 242 Skid Steer Loaders Power Train Solenoid Valve and Mounting (Parking Brake) - Remove and Install
3524B Engine for Caterpillar Built Machines Vibration Damper - Remove and Install
R1600G Load Haul Dump Hydraulic System Relief Valve (Line) - Test and Adjust
R1600G Load Haul Dump Hydraulic System Relief Valve (Main) - Test and Adjust
R1600G Load Haul Dump Steering System Neutralizer Valve (Implement and Steering) - Test and Adjust
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Operational Checks (Brake, Hydraulic Fan System)
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Operational Checks (Power Train)
A Procedure for Installation of the Rotor Drive is Available{5611}
3524B Engine for Caterpillar Built Machines Exhaust Manifold - Remove and Install
226 and 242 Skid Steer Loaders Power Train Axle - Assemble
226 and 242 Skid Steer Loaders Power Train Axle - Install
814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Machine Systems Hydraulic Tank - Disassemble
814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Machine Systems Hydraulic Tank - Assemble
814F Wheel Tractor, 815F Soil Compactor and 816F Landfill Compactor Machine Systems Cab - Install
D350E Series II and D400E Series II Articulated Trucks Power Train Solenoid Valve (Lockup Clutch)
789C Off-Highway Truck Steering System Steering Accumulator - Test and Charge
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Air System and Brakes Introduction
3524B Engine for Caterpillar Built Machines Fuel Priming Pump - Remove and Install
120H and 135H Motor Graders Machine Systems Fan and Gear Motor (Hydraulic Fan) - Install
R2900 Load Haul Dump Fire Extinguisher Location
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Transmission