Chain (Drive) - Install
`
226 and 242 Skid Steer Loaders Power Train
[RENR4834]
226 and 242 Skid Steer Loaders Power Train
Axle - Install
226 and 242 Skid Steer Loaders Power Train
Chain (Drive) Tension - Adjust
POWER TRAIN
DRIVE GP
226 and 242 Skid Steer Loaders Power Train
Chain (Drive) - Install
1.1. Installation Procedure
Installation Procedure
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "AVSpare Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on AVSpare products. Dispose of all fluids according to local regulations and mandates. |
- The front axle assemblies and the rear axle assemblies are driven by different drive chains. The drive chains are installed on Drive Sprocket (B) and Drive Sprocket (D). The drive sprockets are mounted on the drive shaft of the hydrostatic piston motor. The two drive sprockets are the same component. The drive sprocket on the hydrostatic piston motor has sprocket drives on different planes. The drive sprockets on the front and rear axles are the same component. The sprockets on the front and rear axles are mounted at 180 degrees of opposite direction. Note that Sprocket (A) is in line with Drive Sprocket (D) and that Sprocket (C) is in line with Drive Sprocket (B). The drive sprockets are installed in a manner that will allow the drive chains to turn in a straight line. If any of the sprockets are installed incorrectly the drive chains can not be installed properly. Note the orientation of all of Drive Sprocket (B) and Drive Sprocket (D). Note the orientation of Sprocket (A) and Sprocket (C) on the axles.
Show/hide table
![]() | |
Illustration 1 | g00577375 |
- Install drive chain assembly (13) .
Show/hide table
![]() | |
Illustration 2 | g00913436 |
- Repeat Step 2 for the other drive chain assembly.
- Install the spacer. Refer to Disassembly and Assembly, "Piston Motor (Hydrostatic) - Install". Refer to Step 6 through Step 12.
- Refill the drive chain oil. Refer to Operation and Maintenance Manual, SEBU7468, "Drive Chain Case Oil - Change".
End By:
- Install the tire and rim. Refer to Disassembly and AssemblyRENR4838, "Tire and Rim - Remove and Install".
- Tilt the cab. Refer to Disassembly and AssemblyRENR4838, "Cab - Tilt".
Information System:
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System
MID 028 - CID 0609 - FMI 03
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System
MID 028 - CID 0608 - FMI 02
R2900 Load Haul Dump
Plate Locations and Film Locations
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System
MID 028 - CID 0607 - FMI 02
3524B Engine for Caterpillar Built Machines
Engine Oil Pump - Install
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Hydraulic and Steering System
Introduction
554 and 574 Forwarders Power Train
Filling and Flushing the Hydrostatic System - Test
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System
MID 028 - CID 0606 - FMI 02
IT62G Series II Integrated Toolcarrier and 950G Series II and 962G Series II Wheel Loaders
Capacities (Refill)
D350E Series II and D400E Series II Articulated Trucks Power Train
Priority Valve
3524B Engine for Caterpillar Built Machines
Engine Oil Pump - Remove
Installation Procedure for the New Traction Control System{5051}
226 and 242 Skid Steer Loaders Power Train
Chain (Drive) Tension - Adjust
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Hydraulic and Steering System
Piston Pump (Hydraulic and Steering)
Field Installation Of 3Z-5855 Jake Brake Modification {1119, 1129, 7314}
TK711, TK721, TK722 and TK732 Track Feller Bunchers
Safety Messages
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System
MID 028 - CID 0609 - FMI 05
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System
MID 028 - CID 0609 - FMI 06
TK711, TK721, TK722 and TK732 Track Feller Bunchers
Additional Messages
D350E Series II and D400E Series II Articulated Trucks Power Train
Transmission Hydraulic Control
PMG3516 Power Module
Roading
R2900 Load Haul Dump
Battery Disconnect Switch
TK711, TK721, TK722 and TK732 Track Feller Bunchers
Specifications
R1600 Load Haul Dump Machine Electrical System
Torque Converter Lockup Control