216 and 232 Skid Steer Loaders 3024 Engine Supplement Gear Motor (Fan) - Remove Caterpillar


Gear Motor (Fan) - Remove
`
216 and 232 Skid Steer Loaders 3024 Engine Supplement [RENR4833]
HYDRAULIC SYSTEM
MOTOR GP
216 and 232 Skid Steer Loaders 3024 Engine Supplement Gear Motor (Fan) - Remove
216 and 232 Skid Steer Loaders 3024 Engine Supplement Gear Motor (Fan) - Install
1.1. Removal Procedure

Removal Procedure

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     9L-8493     Cap (7/16 JIC)     1    
9S-5518 Plug (7/16 JIC)     1    
6V-9510 Face Seal Plug (1 - 14 THD)     2    
6V-9831 Cap As (1 - 14 THD)     2    
6V-9511 Face Seal Plug (1 13/16 - 12 THD)     2    
6V-9832 Cap As (1 13/16 - 12 THD)     2    

Start By:

  1. Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".

------ WARNING! ------

Personal injury can result from hydraulic oil pressure and hot oil.

Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.

Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.

----------------------


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on AVSpare products.

Dispose of all fluids according to local regulations and mandates.



NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


Note: SERVICE DATA: TOOLING (A) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.

Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.




    Illustration 1g00911005

  1. Disconnect tube assemblies (1). Disconnect hose assemblies (2). Remove bolts (3). Remove fan drive assembly (4) .



    Illustration 2g00911009

  1. Remove bolts (5). Remove fan (6) .



    Illustration 3g00911010

  1. Remove adapter (7) .



    Illustration 4g00911012

  1. Remove connectors (8). Remove bolts (9). Remove motor (10).

Information System:

120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Air System and Brakes Parking Brake
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Air System and Brakes Service Brakes
143H and 163H Motor Graders All Wheel Drive All Wheel Drive System
143H and 163H Motor Graders All Wheel Drive Operational Checks
143H and 163H Motor Graders All Wheel Drive Machine Preparation for Troubleshooting
216 and 232 Skid Steer Loaders 3024 Engine Supplement Water Pump - Remove and Install
216 and 232 Skid Steer Loaders 3024 Engine Supplement Water Temperature Regulator - Remove and Install
D250E Series II and D300E Series II Articulated Trucks Power Train Transmission Planetary
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System Ride Control System - Not Equipped With a Relief Valve
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Location of Components (Hydraulic System)
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Air System and Brakes Air Control Valve (Service Brakes)
PS-360B Paving Compactor Cooling System Water Temperature Regulator - Replace
216 and 232 Skid Steer Loaders 3024 Engine Supplement Gear Motor (Fan) - Install
216 and 232 Skid Steer Loaders 3024 Engine Supplement Radiator and Hydraulic Oil Cooler - Remove
216 and 232 Skid Steer Loaders 3024 Engine Supplement Radiator and Hydraulic Oil Cooler - Install
216 and 232 Skid Steer Loaders 3024 Engine Supplement Air Cleaner - Remove and Install
143H and 163H Motor Graders All Wheel Drive General Information
AP-655C and BG-2255C Asphalt Pavers Drag Conveyor and Auger Conveyor Systems Introduction
R2900 Load Haul Dump Gauges
D250E Series II and D300E Series II Articulated Trucks Power Train Output Transfer Gear Group
RM-350B Road Reclaimer/Mixer Power Train Piston Pump Control (Rear Propel Pump) - Test and Adjust
R2900 Load Haul Dump Indicators
R2900 Load Haul Dump Light Switches
216 and 232 Skid Steer Loaders 3024 Engine Supplement Muffler - Remove and Install