Engine - Remove
`
216 and 232 Skid Steer Loaders 3024 Engine Supplement
[RENR4833]
216 and 232 Skid Steer Loaders 3024 Engine Supplement
Muffler - Remove and Install
216 and 232 Skid Steer Loaders 3024 Engine Supplement
Engine - Install
ENGINE ARRANGEMENT
ENGINE AR
216 and 232 Skid Steer Loaders 3024 Engine Supplement
Engine - Remove
216 and 232 Skid Steer Loaders 3024 Engine Supplement
Engine - Install
1.1. Removal Procedure
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | FT-2741     | Chain Assembly     | 1     |
Start By:
- Remove the battery. Refer to Disassembly and Assembly, "Battery and Battery Cable - Seperate and Connect".
- Remove the radiator and hydraulic oil cooler. Refer to Disassembly and Assembly, "Radiator and Hydraulic Oil Cooler".
- Remove the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
- Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and Install".
- Remove the starter. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
- Remove the air cleaner. Refer to Disassembly and Assembly, "Air Cleaner - Remove and Install".
- Tilt the cab. Refer to Disassembly and Assembly, "Cab Tilt".
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
- Remove cable straps (1). Loosen clamps (2). Remove hoses (3). Remove nut (4). Remove the wire. Disconnect harness assemblies (5) .
Show/hide table
![]() | |
Illustration 1 | g00914921 |
- Loosen clamp (6). Disconnect the hose. Remove clip (7). Remove clip (8). Position the governor control cable out of the way. Disconnect harness assembly (9) .
Show/hide table
![]() | |
Illustration 2 | g00827916 |
- Remove cable strap (10) .
Show/hide table
![]() | |
Illustration 3 | g00827914 |
- Remove bolts (11). Loosen clamp (12). Remove the hose. Disconnect harness assembly (13). Loosen clamp (14). Disconnect the hose.
Show/hide table
![]() | |
Illustration 4 | g00914922 |
- Disconnect harness assembly (15). Remove cable strap (16) .
Show/hide table
![]() | |
Illustration 5 | g00827923 |
- Support the hydrostatic piston pump with a suitable device. The weight of the pump is approximately 59 kg (130 lb). Remove bolts (17) .
Show/hide table
![]() | |
Illustration 6 | g00827960 |
- Disconnect harness assembly (18). Remove bolt (19) .
Show/hide table
![]() | |
Illustration 7 | g00827962 |
- Attach a suitable lifting device and Tooling (A) to the engine.
Show/hide table
![]() | |
Illustration 8 | g00827898 |
- Remove nut (20).
Show/hide table
![]() | |
Illustration 9 | g00827933 |
- Remove bolt (21). Remove bolts (22). Loosen two bolts (23). Remove mount (24) .
Show/hide table
![]() | |
Illustration 10 | g00914923 |
Show/hide table
![]() | |
Illustration 11 | g00914924 |
- Remove nut (25). Remove bolts (26). Remove the engine. The weight of the engine is approximately 320 kg (700 lb).
Show/hide table
![]() | |
Illustration 12 | g00914925 |
Show/hide table
![]() | |
Illustration 13 | g00914926 |
Information System:
216 and 232 Skid Steer Loaders 3024 Engine Supplement
Muffler - Remove and Install
R2900 Load Haul Dump
Light Switches
R2900 Load Haul Dump
Indicators
RM-350B Road Reclaimer/Mixer Power Train
Piston Pump Control (Rear Propel Pump) - Test and Adjust
D250E Series II and D300E Series II Articulated Trucks Power Train
Output Transfer Gear Group
R2900 Load Haul Dump
Gauges
AP-655C and BG-2255C Asphalt Pavers Drag Conveyor and Auger Conveyor Systems
Introduction
143H and 163H Motor Graders All Wheel Drive
General Information
216 and 232 Skid Steer Loaders 3024 Engine Supplement
Air Cleaner - Remove and Install
216 and 232 Skid Steer Loaders 3024 Engine Supplement
Radiator and Hydraulic Oil Cooler - Install
216 and 232 Skid Steer Loaders 3024 Engine Supplement
Radiator and Hydraulic Oil Cooler - Remove
216 and 232 Skid Steer Loaders 3024 Engine Supplement
Gear Motor (Fan) - Install
216 and 232 Skid Steer Loaders 3024 Engine Supplement
Engine - Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines
Engine Oil Cooler - Remove
2002/10/07
Changes to the Hood Assembly Improve Service Life {7155, 7251, 7267}
R2900 Load Haul Dump
Remote Control Switch - If Equipped
3500 and 3500B High Displacement Engines for Caterpillar Built Machines
Engine Oil Cooler - Install
Troubleshooting Failures of the Exhaust Tube on 3408E and 3412E Engines{1061}
3054E Industrial Engine
Fuel Injection Pump
2002/09/02
Parts for the Planetary for the A19 Auger Are Now Serviced {5904, 7000}
226 and 242 Skid Steer LoadersEngine Supplement
Engine - Remove
14H Motor Grader 3176C Engine Supplement
Hood - Install
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines
Electronic Service Tools
140H and 160H Motor Graders Engine Supplement
Fuel Priming Pump - Remove and Install