Pump Mounting - Remove and Install
`
226 and 242 Skid Steer LoadersEngine Supplement
[RENR4843]
226 and 242 Skid Steer LoadersEngine Supplement
Engine - Remove
226 and 242 Skid Steer LoadersEngine Supplement
Engine - Install
POWER TRAIN
DRIVE GP
226 and 242 Skid Steer LoadersEngine Supplement
Pump Mounting - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 180-3033 | Stand | 1 |
B | 180-3034 | Stand | 2 |
Start By:
- Remove the engine. Refer to Disassembly and Assembly, "Engine - Remove".
- Use Tooling (A) and Tooling (B) to support the engine. Remove bolts (1). Remove clip (2). Remove adapter plate (3).
Show/hide table
Illustration 2 g00916409 - Remove bolts (4). Remove nylon flange (5).
Show/hide table
Illustration 3 g00916623 - Remove bolt (7). Remove hub (6).
Show/hide table
![]() | |
Illustration 1 | g00916410 |
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 180-3033 | Stand | 1 |
B | 180-3034 | Stand | 2 |
C | 9S-3263 | Thread Lock Compound | 1 |
- Install hub (6). The face of hub (6) must be installed to a dimension of
65.3 ± 2.0 mm (2.60 ± 0.08 inch) from the face of the pump. This dimension is shown in the graphic above as Dimension (X). Apply Tooling (C) to the entire length of the threads on bolt (7). Tighten bolt (7) to a torque of110 ± 10 N·m (80 ± 7 lb ft) .Note: New models of hub (6) are equipped with an internal stop. Slide hub (6) over the shaft until the internal stop on hub (6) makes contact with the shaft. This will maintain Dimension (X).
Show/hide tableIllustration 5 g00916409 - Install nylon flange (5). Install bolts (4).
Show/hide table
Illustration 6 g00916410 - Install adapter plate (3). Install clip (2). Install bolts (1).
Show/hide table
![]() | |
Illustration 4 | g00916623 |
End By:
- Install the engine. Refer to Disassembly and Assembly, "Engine - Install".
Information System:
Bench Test Procedure for a 784B, 784C, 785, 785B, 785C,785D, 789, and 789B Off-Highway Truck Transmission{3030, 3073}
CB-534D, CB-534D XW and CB-564D Paving Compactors Machine Systems
Radiator and Hydraulic Oil Cooler
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders
Electronic Control Module (Power Train)
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System
Proportional Pressure Solenoid Valve - Test
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes
Service Brakes and Retarder System Pressure - Test
554 and 574 Forwarders Power Train
Gearshift Pressures - Test - 574 Forwarder 1FM434-UP
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders
Features
216 and 232 Skid Steer Loaders 3024 Engine Supplement
Pump Mounting - Remove and Install
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes
Service Brakes and Retarder System Leakage - Check
CB-534D, CB-534D XW and CB-564D Vibratory Asphalt Compactors Propel System
Drum Drive Group
CB-634D Paving Compactor Machine Electronic Control System
Water Spray Is Always Off
3054E Industrial Engine
Engine Oil Filter
2002/11/11
New Mirror Has Improved Durability and a New Support that Reduces Vibration {7319}
R2900 Load Haul Dump
Steering Control
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes
Hoist, Torque Converter, and Brake System Troubleshooting
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes
Pulled Unit Hydraulics, Torque Converter, and Brake System Troubleshooting
574B Forwarder Power Train
Power Train Charge System Pressure - Test
Air Conditioning and Heating R-12 All Caterpillar Machines
Machine Preparation for Disassembly and Assembly
2003/04/21
A Sight Gauge for the Transmission Oil Level and an Oil Filler Tube at Ground Level are Available {3030}
2002/09/16
New Pins for the Bulldozer Blade are Now Greased {6061, 6065, 6066}
Air Conditioning and Heating R-12 All Caterpillar Machines
General Information
3500 and 3500B High Displacement Engines for Caterpillar Built Machines
Engine Trunnion - Remove and Install
Air Conditioning and Heating R-12 All Caterpillar Machines
Refrigerant Compressor - Remove and Install
Air Conditioning and Heating R-12 All Caterpillar Machines
Receiver-Dryer - Remove and Install